Books or articles about steels heat treating cycles

More Hossein Mahtabpour's questions See All

What are differences between wettability of SiC nanoparticles and microparticles in Al-matrix composites?

I want to know differences between wettability of these particles Can we improve this property by changing size of paticles?

10 November 2017 9,955 0 View

Books about duplex aging specifically for aluminum alloys

Please introduce me heat treating books that explain about duplex aging heat treatment in aluminum alloys. I have searched in many books but didn't find anything about this topic.

05 June 2017 8,984 2 View

Effective factors on size of gas porosity in aluminum alloys

Please tell me about factors that affect size of gas porosity in aluminum alloys. Thanks.

05 June 2017 10,023 2 View

Comparison between Mg-alloys and Al-alloys applications

What are Mg-alloys production difficulties that causes limitations in application of these alloys rather than Al-alloys?

04 May 2017 7,507 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Why can't academics earn the money they deserve?

Only Journals make money from the articles we have worked on for years. Academics do not earn money from their refereeing. Then shouldn't the solution be a system in which academics can earn...

01 August 2024 6,469 6 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Farhad Rahimi

Dear Hossein,

There are several books covering heat treatment topics. I name some of them to help you out:

1- Hardening, tempering and heat treatment -- by Tubal Cain

2- Practical Heat Treating -- by Howard E. Boyer

3- Steel heat treatment handbook -- by George E. Totten

Best,

Farhad

Hossein Mahtabpour

Thank you Farhad,

These books were very useful.