How to make ppb level concentration ?

Hi, I've N2 gas cylinder and 100 ppm NH3 gas cylinder. With these two cylinders, I'd like to make a ppb level (1- 100) concentration. Any idea how to do that?

01 February 2021 3,264 2 View

What is the proper aldosterone and CORT supplement in ADX mice?

Hi, I am struggling with the stress experiements in ADX mice. i tried 15ug/ml cort in the drinking water for ADX mice, however, the basal plasma cort are much higher than sham controls( 260ng/ml...

21 June 2020 386 1 View

What's the reason for the crossover of illuminated and dark JV curve in CIGS solar cells?

The distinct crossover anomalies are observed in my recent samples. It's explained in the book that there might be a barrier at the interface or in the absorber's near interface region.The barrier...

29 May 2020 675 4 View

How should I hydroxylate tungsten powder for organosilane grafting?

I am having trouble depositing MPTMS/APTES onto tungsten and I am concerned there are not enough hydroxyl groups on the powder surface. So far I have been exposing tungsten to water to hydroxylate...

04 February 2020 4,677 2 View

Could I extract RANK/RANKL/OPG mRNA from peripheral blood samples?

I want to know that whether it is possible to extract RANK/RANKL/OPG mRNA from peripheral blood samples instead of tissue homogenates. Thanks a lot.

07 September 2019 7,431 3 View

How to calculate the area of coverage hole of a disc tessellation?

The locations (centre coordinate x,y) and radii of all the circles are given. How to get the area of the coverage hole (area in green in the figure) ? Radii may not equal to each other. It is a...

11 June 2019 5,127 15 View

For WB, if there were DNA in my protein sample, how can I do?

Hi, everyone, I am working on transcriptional factor, I want to define what protein bind to my specific DNA, after I got the sample that bound to DNA, and use SDS buffer to boil it, I can find the...

24 June 2018 4,582 5 View

How the overall score is related to their subscale scores?

This is the third section of Items Decomposition: How to structure the Scores and Items. This section describes, using the graphical representation, how the score associated with all items in a...

07 June 2018 8,942 4 View

May I know who successfully knock-in target gene in mice? Using what methods?

Would appreciate if you can share how you done it. Thank you.

07 February 2018 2,091 1 View

EMSA-no binding band?

I am doing DNA-EMSA these days, when I try the control EBNA system, it is ok. But when I test my samples, there were no protein binding bands. In the first time, I use the volume suggested by the...

04 December 2017 5,658 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

What is the difference between genotype and haplotype data in the ped format?

Hi everybody In the ped format for genotype, alleles of any SNP are represented by two columns (one for each allele, separated by a space). Is a column sufficient for the haplotype to...

27 February 2021 1,965 1 View