Are there any significant difference on plywood bonding strength between mono species and mixed species plywood?

09 November 2017 0 8K Report

can anyone share their findings towards the bonding strength of plywood made of a single species compared to a plywood made of mixed wood species.

Badges
Science topic

More Nik ahmad farizan nik lah's questions See All

Quantum Capacitance and EDL capacitance difference?

Hi all, hope you are well. Just a quick question, at which (level) does quantum capacitance is much dominant then EDL capacitance? level here means, contribution such as low temperature, or...

20 September 2023 2,987 0 View

How to make even etching using RIE for SiO/Si substrate?

I tried to etch the oxide layer using RIE(4sccm:26sccm, O2: CF4, 50W, 15 mins), however i obtained uneven etched oxide layer. Thus, there is gradient of etch profile (thickness, and roughness)...

08 March 2023 1,668 2 View

Does anybody have a spreadsheet for calculating CIPW norm for bulk chemistry of kimberlites?

12 October 2022 4,472 0 View

Statistical Test for 4 independent variables?

I have 4 independent variables (types of enrichment, types of tanks, mating pairs, strain of zebrafish) (nominal scale) with 1 dependent variable (fecundity of zebrafish/embryos laid) (scale...

27 November 2021 3,399 2 View

Hi, which one is better for metabolites extraction of seed, 70% Methanol or 100% Methanol then add 1 vol of water?

This is for the sample preparation technique for untargeted metabolite profiling by using LC-MS analysis. Thank you.

13 November 2021 5,152 4 View

Does anyone have experience with fixation of cells after Calcein-AM staining?

Hi.. I am about to fix my cells after Calcein-AM stainig because in my reading, Calcein-AM is unable to pass through dead cells. Anyone experience on this? For how long does the staining will...

03 August 2021 1,903 3 View

How do I create a .sdf format ligand database?

Hi everyone. I used to be able to do this and I remember that it involved a command prompt based piece of software but I can't remember what it was. I have a folder full of .mol files (although I...

09 February 2021 1,259 5 View

Can a poor performance result be written for a paper?

I am currently working on a database and I have tried various methods of machine learning and deep learning, all leads to poor classification/prediction. However, this might show that the two...

27 May 2020 8,157 7 View

What is the best device for presenting white noise signals to a participant during TMS-EEG?

I'm trying to come up with a method for presenting white noise signals to a participant during TMS-EEG without using a laptop. If you have experience with this what devices do you use? Or should I...

13 February 2020 634 4 View

What is the current state of Agent-Based Modeling and Complex Systems research in Computer Science?

I am looking to enter the field of Complex Systems or Complexity Science as a postgraduate in my Computer Science faculty, specifically focusing on Agent-Based Modeling. However, I am unclear on...

04 January 2020 9,275 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

A paper on a fossil lycopod?

Dear all, Does anybody have a pdf of this paper? Wood, G.R. and Beeston, J.W., 1986. A late Permian lycopod cone Skilliostrobus sp. cf. S. australis Ash 1979 from Queensland. Geological Survey of...

07 August 2024 4,857 2 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

Can Langmuir constant related to bonding energy (Kl) and Freundlich exponent (1/n) indicative of ads intensity show opposite trends with temperature?

The adsorbate is Arsenic and the adsorbent is a soil

18 July 2024 332 8 View

How to create parameter and coordinate files for ligand in amber when FATAL error (maybe due to duplicate bond specifications) happens?

Hello, I'm trying to create parameter and coordinate files for a drug (PRG-A01) found on the following page: http://www.probechem.com/products_PRG-A01.html I used the guide made by Michael...

17 July 2024 3,472 3 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View