Are the FPGA based emulators of DC motor considered an industrial application?

More Hesham Gad's questions See All

Why the density of the buoyancy liquid should be less than or equal to 1 gr/cm3 in Archimedes experiment ?

28 December 2020 3,887 2 View

How can i redraw the published figures to reproduce them in my articles?

is there an application or website that can be used to redraw and edit the figures to re-publish them without permission from the main author?

21 December 2020 921 3 View

Voice recognition for alQuran Arabic?

How can we compare two audio files, or voice recorder files, according to Al-Quran. Al-Quran has special pronunciation compared to Arabic pronunciation. Is it possible to do the comparison between...

25 November 2020 3,657 7 View

What is the best metric (precision, recall, f1, and accuracy) to evaluate the machine learning model for imbalanced data?

What is the best metric (precision, recall, f1, and accuracy) to evaluate the machine learning /Deep learning model for imbalanced data? how to explain and present the results in the research...

13 July 2020 8,560 16 View

What is the best software to plot Deep Learning model?

I want to plot a good quality figures to use it in the research paper. So, what is the best software to use to plot any deep learning model/Machine learning model?

11 July 2020 2,797 35 View

Can I use anhydrous ammonium phosphate in oil and grease extraction?

hi, can I use anhydrous ammonium phosphate instead of anhydrous sodium sulfate in oil and grease extraction?

23 March 2020 9,987 3 View

How to increase diffusion of liposomes in invitro agar diffusion test ?

during a comparison between nano liposomes loaded with antibiotic and antibiotic itself in invitro antimicrobial assessment , we found that the antibiotic showed more inhibition for the bacterial...

23 February 2020 1,025 3 View

How to calculate the Permittivity of the cotton in the range from 0.5- 1.5 THZ needed to calculate the total pathloss?

I'm new in the field, working on characterization for a model of air , cotton , air in the terahertz band. I need to calculate the Permittivity of the cotton in the range from 0.5- 1.5 THZ needed...

14 December 2019 3,886 2 View

ABAQUS-Early debonding when modelling prestressed concrete slabs strengthened with Near Surface Mounted FRP strips?

I am modeling a prestressed concrete slab strengthened with NSM FRP strips using ABAQUS I'm experiencing early debonding at a lower load than the experimental results I'm modelling the contact...

03 July 2019 1,046 2 View

What are the different factors that affect the contrast of an image?

Medical Imaging

28 May 2019 9,969 8 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

How to do Matrix inversion using FPGA ?

I need to implement matrix inversion in hardware. The size of the matrix can be anywhere from 50 *50 to 8*8. Are ready-made standard codes available or inbuilt modules available with FPGA...

15 February 2021 4,006 3 View

How do I connect DAB DC DC Converter to a battery in matlab simulation ?

I am trying to model a DAB converter and I need to observe the power transfeered to the load side on varying the phase shift between two bridges, hence I couldnt take a constant load e.g...

09 February 2021 6,489 3 View

Steps for Hardware Implementation of Max Log MAP Decoder simulated in MATLAB?

How to implement max Log MAP algorithm turbo decoder on FPGA? Simulation is done on MATLAB. What are the next steps to be followed? Do I need to use HDL Coder feature in MATLAB? Is it needed to...

07 January 2021 4,405 4 View

Is there a generalized method to derive current-mode model of any DC-DC converters?

Hi all, As new DC-DC converters are being proposed, associated control method should be proposed and based on the small-model signal analysis of the DC-DC converters. Using average space state...

06 January 2021 7,247 3 View

How can I verify the design on the FPGA ZedBoard?

I have designed AXI Interconnect to connect 4 masters and 1 slave using SystemVerilog and Vivado Tool. The simulation stage of the design is working well. In the design, there are more I/O pins...

06 January 2021 8,487 2 View

How to interact with internal memory of FPGA and connect it a signal or array inside a module?

I am trying to implement a processor tile on FPGA using vivado but it is taking too long to synthesize design due to large amount of Instruction and Data Memory. Currently, I have put complete...

05 January 2021 8,349 1 View

Gerardo Maximiliano Mendez

Yes, it is

Heshmat Soliman Aldesuquy

Dear sir,

I am sorry, I have no answer because I am not interest.

Hesham Gad

Dear Prof, Heshamat

You don't need to answer the question if it is not in your field

Amr Ezz Eldin Rashed

http://redpitaya.com/features-2-2/

i think this device is useful for your test

Arnaud Dion

I've done exactly this some years ago. So I think that it's a pertinent application.