Are adaptive link rates or burst mode operation used to save power in optical access networks?

23 September 2014 1 8K Report

How do these above techniques reduce the power of consumption in access networks?

Power consumption can be reduced by accessing the device points by simulation. They can also be used for monitoring and further utilization of conceptual reduction.

Badges
Science topic

Similar topics
Engineering
Control Theory

More Amit Kumar Garg's questions See All

What is the minimum number of studies in each category required for a multiple subgroup analysis to be viable in a meta-analysis?

Cochrane Handbook mentions subgroup analyses are only warranted if there are more than 10 studies (I have 28), and if they are distributed evenly among categories of subgroup. I am wondering if...

17 February 2021 3,467 4 View

How do you interpret multiple meta-regression in STATA?

Please could someone recommend a resource that explains performing meta-regression with multiple moderators. I have read the STATA META ANALYSIS REFERENCE MANUAL, but this only gives examples of...

17 February 2021 7,376 1 View

DMSO concentration in cell culture? Precipitating while PBS is added?

I am testing a compound on RAW 264.7. the compound is soluble in DMSO. but to ensure that final concentration of dmso is not more than 0.1%, we are first dissolving it in dmso and then diluting it...

11 February 2021 1,136 3 View

How do you incorporate a study that used non-parametric analysis into a meta-analysis where majority of studies used parametric?

I am calculating Hedge's g for effect sizes, so I am pulling means, SDs, and Ns, from each study. However, one study did a Mann-Whitney U test, and so reports Mean Rank, Sum of Ranks, U, Z, and r...

31 January 2021 1,182 5 View

How to show a protein is being dimerized in SDS-PAGE gel?

A protein dimerizes through CTD. I have expressed CTD of protein with two different tags. Now, I want to show that these CTD of protein dimerize in a pull-down assay. But my doubt is that if the...

29 January 2021 7,529 4 View

ANSYS APDL RC Beam modelling?

Hello I have modelled RC beam in ANSYS apdl. first create volume, then create keypoints & create a line joining that keypoints to make reinforcement. I am working on thermal analysis, for...

20 January 2021 7,344 2 View

ANSYS APDL tabular entry related?

Hello I want to add thermal convection load on specific area of concrete volume. it asks for film coefficient which is a constant value but the bulk temperature has no. of values that i have as...

18 January 2021 6,627 1 View

What are the impacts of pKa1and pKa2 in drug absorption ?

Pregabalin is a crystalline solid with a pKa1 of 4.2 and a pKa2 of 10.6. what insight can i get from this aforementioned information during drug design. What is the difference between pKa1and pKa2.

28 December 2020 7,237 3 View

What is the best way to maintain constant concentration of a volatile organic liquid in an open experimental set-up?

The purpose is to keep a NAPL (eg Toluene) concentration constant in an open tank set-up.

27 December 2020 7,325 2 View

How i can input temperature depedent stress strain curve for concrete & steel in ansys?

i am working on thermo-mechanical analysis of RC beam using ANSYS. i want to input temperature dependant stress strain curve in ansys. i tried using elastic > multilinear but a warning attached...

23 December 2020 9,928 2 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

1. What is the impact of having different scales in a survey? and how can we solve this problem before and after data collection (Literature)?

1. What is the impact of having different scales in a survey? and how can we solve this problem before and after data collection (Literature-based reflection)? Thank you for your time and for...

03 March 2021 2,870 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View