Anyone knows in CMG-STARS, how to output the total mole fraction or total mole numbers for oil phase and water phase, respectively?

08 February 2017 1 839 Report

Anyone knows in CMG-STARS, if there are more than 2 pseudo components, how to output the total mole fraction or total mole numbers for oil phase and water phase, respectively?

I've add "OUTSRF GRID PRES SG SO SW TEMP X Y " in the dat file, while the result only shows X, Y for each pseudo component instead of the total.

Thanks.

Ali Jamali

I assume you want to calculated moles of fluids produced from producers. Right? Add this line to your .dat file: *OUTSRF *WELL *MOLE and it should take care of it.

More Siyuan Huang's questions See All

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

No title

Does anyone have the experience of using Taq Man probes in the QIAGEN Rotar- Gene qPCR machine?

01 March 2021 5,311 1 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Has anyone used the Illumina ITS1 primer sets?

Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...

25 February 2021 6,969 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View