Any one interested for collaborations (Selective Laser Melting (SLM) of Nickel- and Titanium-based alloys)?

More Aleksei Obrosov's questions See All

Any one interested for collaborations (FIB sample preparation for TEM investigation)?

Our group is working with different coating systems and materials. We need somebody, who can help us to do FIB sample preparation. We are planning to wirite few publications. Sharing authorship...

10 November 2018 8,617 3 View

How to interpret the DSC analysis of Zr1Nb alloy with and without additional element??

We have Z1Nb alloy and provided DSC analysis with and without additional Ti. We found that alloy has two transitions. The low-temperature transition, occurring between about 500°C and 650°C. The...

06 July 2017 7,259 1 View

Any one interested for collaborations (XPS measurements for coatings)?

Our group is interested to do some XPS measurements for coatings and write few paper with enough high impact factor (> 1,5). We need somebody, who can help us interpreted our XPS results and...

05 June 2015 9,227 7 View

Any one interested for collaborations (FIB sample preparation for coatings after erosion and corrosion)?

Our group is working with coatings and we have done few erosion tests. We need somebody, who can help us to do FIB sample preparation for our coatings. We are planning also to do some corrosion...

05 June 2015 2,029 10 View

How can we measure the thickness of TEM samples after dimpling?

We are preparing a sandwich structures of our coating (Cr2ALC) and we could not measure a thickness of the samples after dimpling. Is it possible to measure it and how? Thanks in advance for your...

04 May 2015 5,636 5 View

Could anyone tell me please, how could I measure porosity of PVD coatings?

I have several coatings and would like to compare them. I choose porosity as the main properties for comparing. But how could I measure porosity of PVD coatings? Thank you in advance

02 March 2015 5,032 10 View

Where can i find the paper about solid solution of aluminum in iron Fe(Al) or any paper about Fe-Al diagramm Al content (0-25 at. % Al)?

Thank you

01 January 1970 4,418 2 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Interested in a SCOPUS collaboration?

Hi RG family. My team and I are working on some SCOPUS publications and we need co-authors who are willing and capable of undertaking both qualitative and quantitative-based studies. The scope...

02 August 2024 7,843 0 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Is there any Indian Company or Startups, from any universiy or IITS, which manufacture Gas Chromatography instrument , i want to make a custOmized G?

or we can collaborate

01 August 2024 6,705 2 View

Have you heard about Technological Surveillance on Oceanographic Research Vessels?

It is important to highlight that technological surveillance on oceanographic vessels is a collaborative effort in which different specialists work together to effectively leverage technology in...

31 July 2024 1,633 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Slim Kaddeche

I'm interested to work with you on this topic. Please send me more informations.

Best regards,

Yunhui Chen

Hi, Our research group is experienced with metal metallurgy and SLM. If you are interested, plz contact [email protected] for further information

Sonia I. G. Fangaia

I'm interested. Please send me more informations. Best regards