Any advice on the tapping of an inductance in a MATLAB?

Akhilesh Panwar @Akhilesh_Panwar

11 November 2013 0 7K Report

For a line with inductance, I want to provide taps at 30 % of the inductance.

Badges
Science topic

More Akhilesh Panwar's questions See All

What will happen to power system stability if, HVDC line is install parallel to the EHV AC line ?

For improving the system stability, what will happen if a HVDC line parallel to the EHV AC in installed.

11 December 2016 1,149 1 View

What is the transfer function model of solar PV ?

Is there any transfer function model of solar PV for analyzing the response for disturbance like shading etc.

11 December 2016 174 4 View

How can I design the PI controllers for decoupled control of VSC in grid connected solar PV?

I am designing the decoupled form of control mechanism for VSC (Inverter) in grid connected solar PV. I am unable to find the proper method of designing the same. What should be the criteria we...

02 March 2015 6,292 4 View

What are the different advance schemes for TCR in reactive power compensation?

I would like to know the recent trend in the reactive power compensation by the help of TCR.So for the same if anybody have the paper for recent trend in the mentioned field then kindly reply.

05 June 2014 8,791 5 View

How much solar PV can affect the system stability and what counteracts for improving the system stability?

Solar PV affect the system stability. It will exacerbate the situation when there is high penetration as well as when there is less penetration. How to measure the online parameter of the system...

03 April 2014 3,844 2 View

What is the present scenario of a smart grid and what are the research opportunities (Related to Solar PV in the Smart Grid) in this sector?

Want to know the trends that what actually going on around the world and what are the opportunity available for solar technology in the smart grid? what are the issues of integration of solar...

31 December 2013 5,925 4 View

What are the research areas of integration of renewable energy sources with grid?

What are the research areas available for improving the power quality issues with the help of renewable energy source penetration into grid?

31 December 2013 646 2 View

Which is the best way to calculate the total area required for a solar panel?

I am calculating the total area of a solar panel for a particular load demand by considering the power, but if I consider total energy required for a day and do my designing according to energy...

09 October 2013 6,829 8 View

Selection of a system based upon cost effectiveness - can anyone help?

My question is about the selection of plant systems. If we need to select the plant according to cost effectiveness than whether I should go for a system which is less efficient and less cost per...

08 September 2013 6,120 7 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View