Adhesive for aluminum sheet and HPL?

10 May 2016 1 10K Report

we are bonding aluminum sheet to the HPL using epoxy resin and woven roving 150GSM glass mat. whenever i have bonded i am getting air entrapment in the panel. please give me the information on which is best adhesive for aluminum with HPL bonding.

Pon sudhir Sajan

Dear Pramod

Try the followings,

1.Liquid Weld for heavy duty work

2.cyanoacrylate for strong adhesive and week cohesive.

3.Hot or Silicone Glue

Badges
Science topic

More Pramod Marru's questions See All

Hello Researchers, Can anyone guide me on estimating the Leaf Area Index (LAI) of wheat using only weather and soil parameters? Is it possible?

I need to estimate the LAI of a wheat crop using only weather and soil parameters. Can anyone please help me?

28 July 2024 4,886 2 View

Can we measure the 2θ variation within a 5° range on a Bruker D2 Phasor XRD? is it compatible with diffraction angles (2θ) below 10°?

Can we measure the 2θ variation within a 5-degree range on a Bruker D2 Phaser XRD machine? I have experienced problems with diffraction angles (2θ) below 10 degrees. Is this range within the...

13 July 2024 2,615 4 View

To model Carbon quantum dots(CQDs), which CIF file should be selected?

I have doubts about which CIF file should be selected to design the carbon quantum dots. Any help or suggestions would be greatly appreciated. Thank you very much for your assistance.

19 June 2024 7,541 1 View

How to perform the DFT calculation on the mechanism of Photocatalytic CO2 reduction with water?

Dear Researchers, I hope this email finds you well. I am currently working on research involving DFT calculations to study the mechanism of CO2 reduction using a catalyst with water as the...

14 June 2024 4,612 4 View

Why and how the electrochemical response of boron-doped diamond (BDD) electrodes is not stable over time in ferro-ferri redox mediator electrolyte?

I am trying to utilize boron-doped diamond electrodes for developing electrochemical biosensors. During the electrochemical measurements, it was observed that the current response varies with...

10 June 2024 6,311 1 View

How to convert unit eV to V of the valence and conduction band position of semiconductor?

This question asks for a detailed explanation of the conversion process between these units in the context of semiconductors.

22 May 2024 1,892 1 View

LR reaction producing colonies without my Insert. What could be the issue?

I am trying to clone the cowpea gene (3.5Kb) under the control of the 35s promoter (Gateway plasmid pK7WG2D). I used pDONR222 for the BP reaction. I got the positive colonies, and then sequencing...

01 May 2024 8,489 2 View

Can Metabolic Disorders cure by medicine,sustitutes,gens,and stemcell excercises etc?

Metabolic disorders occur due to our proper habits of eating process and remineralisation in the mouth. Like food, water, and liquids, etc. Due to mutations in all our food in saliva, the...

22 April 2024 1,959 3 View

What temperature is needed to eliminate carbon from the catalyst through calcination?

I have to calculate the carbon content present in the catalyst from the TGA plot. Does anybody have an idea?

17 April 2024 4,718 2 View

What are the issues in the learning of English vocabulary as a second language learner?

Issues in the vocabulary, Problems, or obstacles. Learner learn English as a second language. Learners are High school students faces difficulties in acquiring sufficient vocab.

09 April 2024 5,199 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

How to solve "1 elements have missing property definitions" in Abaqus?

I am creating a single element model in Abaqus of a composite material. My goal is to match the stress-strain curve of the material which was obtained experimentally. I am using VUMAT for Fabric...

07 July 2024 10,036 5 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

Can someone help me to model a core-shell nanostructure in GDIS and subsequently prepare the fdf file for using in SIESTA?

I am very new to the material modelling in GDIS. So, I want to learn how to model a nanostructure specifically core-shell in GDIS.

28 June 2024 5,224 0 View