What is design time distributed delay neural network?

I'm using Newdtdnn model in neural network toolbox of matlab..........But i'm not getting any info about its learning or training process

07 August 2016 2,545 0 View

I need to model my data with fuzzy model in matlab where i need to calculate mean square error for the training set but the code shows error.?

04 May 2016 782 3 View

Can anyone suggest a problem/application area where I can do intention mining with multi agent systems?

06 July 2014 2,543 2 View

SMS data set required

06 July 2014 8,030 0 View

Can anyone suggest a new scenario for process mining?

I've gone through some scenarios, like hospital data process mining and restaurant process mining, but want to find a scenario that is not only new but whose log data is also accessible.

05 June 2014 8,818 5 View

What agent based simulation software will also create a log file? And is it freeware?

I need a software to create a log file for agents.

02 March 2014 2,923 3 View

Which journal has the greatest impact factor in data mining field?

List of international journals in data mining.

10 November 2013 9,275 9 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View