Why do semicircle and Linear region appear in Nyquist plots in Electrochemical Impedence Spectroscopy?

11 November 2014 1 7K Report

What is the meaning of electron/charge transfer limited process which we assign to semicircle and mass transfer limited process which we assign to linear part?

What actually happens there consider polyaniline as example?

Rasu Muruganantham

The EIS semicircle and Linear region is due to a combination of kinetic and diffusion processes. This is my simply & short ans. If you refer the following article may be very useful for your qusn.

Int. J. Electrochem. Sci., 7 (2012) 345 - 353

Badges
Science topic

More Mohit Saraf's questions See All

How to calculate Areal Capacitance?

I have calculated specific capacitance of 200 F g-1. Now I wish to calculate Areal Capacitance. What is the formula? Electrodes: working Glassy carbon electrode of 3mm diameter (0.0707...

05 June 2019 2,442 5 View

How porosity and surface area affect supercapacitor performance (and other electrochemical applications) ?

Usually, high surface area and porosity are reported to be the primary reasons for good electrochemical sensing and supercapacitor performance. Please explain what exactly happens with high...

05 June 2019 5,261 6 View

What are the parasitic reactions (between electrode and electrolyte), which affect coulombic efficiency of Supercapacitors?

Please give some details. Why it happens in particular for battery like electrodes?

05 June 2019 9,804 2 View

Is it necessary that a composite of metal oxide and rGO should always exhibit better energy storage properties compared to only metal oxide and rGO?

Kindly shed some light on it. In my case, the rGO alone is providing better supercapacitor properties than composite.

03 April 2019 9,197 4 View

How to make composite using ultrasonication, when one of your constituents is Grphene? What should be the ratio of both participating materials?

Suppose, I want to make a composite of MOF and graphene. I wish to study the effect of relative content of participating constituents on the electrochemical properties. How to choose the ratio for...

05 June 2018 868 5 View

Expected Impact factor of Chemistryselect ?

New journal of Wiley-VCH

31 December 2017 8,575 51 View

How to differentiate soild-state thermolysis, calcination and annealing ?

Can solid state thermolysis and calcination be called same at any particular conditions ?

07 August 2017 4,145 1 View

How to determine linear range of a biosensor ?? Which is the easiest and best method ??

There are various methods to determine it. Can anyone show with example their suitable employed method ??

05 June 2017 4,953 1 View

Why in some cases Binder free electrode works well (stable ~95% after 1000 cycles) during continuius charging discharging of supercapacitor test ?

I am trying one coordination polymer as electrode material on glassy carbon electrode. It is showing good stability. What can be the reason?

05 June 2017 4,520 7 View

Among reduced graphene oxide (rGO) and nitrogen dooped reduced graphene oxide (NRGO), whose conductivity is more and why?

I have observed higher values of supercapacitance of NRGO than rGO, which has better dispersion than rGO. But what can be the possible reason of higher supercapacitor performance? Has it something...

02 March 2017 655 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View