While the grain size is measured by both Debye Scherrer formula and Williamson Plot , what is the reason for the difference in their values?

16 April 2024 0 5K Report

Also for obtaining perfect linear fit in Williamson plot what are the steps we may follow?

Badges
Science topic

Similar topics
Chemistry

More Dr G. Kiruthiga's questions See All

Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

What is the best method for preparation of Polymeric nanoparticles for co-delivery?

We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.

09 February 2021 7,086 8 View

OmniScriptum Publishing Group?

Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...

08 February 2021 5,611 3 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

How much Ti and B (in ppm) is required for effective grain refinement and why?

To have the desired grain size in 6061 and 6063 Al alloy, what should be the minimum % of Ti and B pick up and what is the chemistry/metallurgy behind that?

07 January 2021 9,305 2 View

How to make AlV50% alloy by thermit route?

Kindly provide the technical papers/patents on the production of AlV50% alloy by thermit route, by using V2O5

05 January 2021 2,471 3 View

Apart from deoxidation what are the other applications of Ferro Aluminum (FeAl) and Al wire?

FeAl and Al wire has applications in Steel for deoxidation. I want to know the other application of various grades of FeAl. Does Al wire also has other applications apart from deoxidation? Regards

27 December 2020 8,435 1 View

From the EDAX analyses if the material which is coated is not observed in maximum percentage then how can interpret the results?

If we doped metal oxide to semiconducting material in different ratios then the property of the resultant material will be increased.But in some lower ratios when we go through the elemental...

16 December 2020 8,190 2 View

Is there is any reference if someone is using Ti sponge cored wire instead of FeTi 70% cored wire for plain carbon steel?

There is a different behavior in carbon steel and stainless steel. Drastic low recovery in carbon steel due to high melting temp. But in ss , working temp is high so dissolve at 1668 degree temp....

16 December 2020 8,765 8 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

What might be the reason for obtaining two bands in plant genomic DNA extraction?

I got a thin band and a thick band i guess it would be the genomic DNA and the 260/280 ratio is 3.

21 February 2021 6,523 6 View

Methodological confusions regarding deductive and inductive reasoning, hypothesis and theory test?

Hi Colleagues- What do you think about the following methodological issues: 1. Is it methodologically wrong to formulate quantitative research questionnaire based on inductive reasoning? 2. Is it...

21 February 2021 4,634 6 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View