Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

Why are we measuring gel content of NBR latex? Does gel content related to the amount of cross-linked in a polymer?

Hi good day to everyone! I am actually studying the gel content of synthetic latex. Refer to ASTM 3616, gel content is measure of insoluble rubbers in the chosen solvent. So, I just would like to...

07 February 2021 605 4 View

How to delete a copy of a paper, and how to delete a co-author's name?

I mistakenly uploaded a copy of the same paper and entered my alternative name. How to delete them out? (I couldn't navigate to the right buttons to do it. So from where to where is what I don't...

07 January 2021 7,694 6 View

What effect will different solvents have on the ATRP reaction?

I want to do an ATRP reaction, synthesize an ATRP initiator, use DMF as a solvent, and mix DMF, BIBB and TEA to turn red. Why does it turn red? Xylene has been used as a solvent before, and there...

04 January 2021 8,034 3 View

Species identification.Who can tell me the scientific names of these Gastropods?

Species identification. I've been doing research on communities of marine macrobenthos recently, but some of them can't be identified, which hinders my research. Who can help me identify these...

14 December 2020 8,357 3 View

Cell shrinkage during ROS assay(H2DCFDA)?

Hi! I'm Yu, studying about health of MSC. These days, I'm doing ROS assay with H2DCFDA which requires 5~30 minutes of staining with PBS or HEPES or HBSS. In our lab, We use PBS w/o Mg/Ca for...

13 December 2020 8,813 9 View

Can I fix the cells after H2DCFDA assay for FACS analysis?

Hi ! I'm Yu, and planning to analyze ROS assay with H2DCFDA(Thermo) on MSCs. A lot of protocols instruct that treat H2DCFDA at specific concentration for 5~30 min, 20~30 min of recovery time...

10 December 2020 973 1 View

How to reconstruct a Lamb wave by a series of pulses superposed?

Lamb wave is useful for solid structure health monitoring, and it consists many modes. Unlike ultrasonic bulk wave, when given a pulse excitation (for example, 5-cycle sinusoidal pulse), only...

08 December 2020 5,440 8 View

How to interpret the significant effect of covariates when conducting a Two-way ANCOVA?

06 December 2020 8,560 4 View

Did anyone do microglia Oil Red O staining?

I need to stain adiposome in microglia, but I don't know how to confirm that are really success? method : Removed media and washed cells with PBS, then added 4 % paraformaldehyde for 20 minutes at...

24 November 2020 2,359 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View