What's the effect of Metakaoline on Toughness of Concrete?

Alyaa Al-Attar @Alyaa_Al-Attar

03 March 2018 1 1K Report

I'd like to get some facts on Metakaoline admixture on Mechanical Properties of Concrete

Messaoud Saïdani

Hello Alyaa,

The following articles may have the answer to your question:

1- http://www.estij.org/papers/vol3no32013/21vol3no3.pdf

2- http://www.jairjp.com/OCTOBER/06%20VIKAS.pdf

3 - https://www.ijsr.in/upload/1980868044Chap_20.pdf

Best wishes

Badges
Science topic

More Alyaa Al-Attar's questions See All

Hi I need 2020 6G and 2020 network coding references to cite soon in my 6G network coding paper ?

I have a paper at the last stage of publication on Q1 journal and I was asked to add 2020 references regarded 6G and network ciding

03 October 2020 5,177 3 View

How to use Tresca criterion in Abaqus VUMAT?

Hello, I know that Abaqus uses Mises yield criteria by default, and I have heard that if I want to use Tresca then I need to implement this in a VUMAT subroutine (for Abaqus/Explicit). I'm sure...

06 March 2020 2,435 3 View

Which software allows high quality schematic drawings for publications?

Hello, I have spotted a number of high quality schematic diagrams, such as the one attached here, from publications. Which software is able of reproducing such high quality schematic...

06 March 2020 4,460 3 View

Why does increasing strain hardening exponent result in less material necking?

Hello, According to the power law, Stress=K*strain^n. Could someone please explain why an increase in strain hardening exponent n results in less material necking from this equation? Please see...

15 February 2020 3,984 4 View

How do I make Abaqus stop the simulation once a critical value of PEEQ has been reached?

Hello, I am doing a series of metal forming simulations in Abaqus. I want the simulations to automatically stop when a critical value of PEEQ (or some other variable) has been reached, in order...

05 February 2020 5,114 4 View

How can I show through thickness stresses along a non-linear bending path in Abaqus?

Hello, I am doing a non-linear beam bending / forming analysis in Abaqus. I want to to get results for the stresses through the thickness direction, where the top fibre will be in tension and the...

17 January 2020 7,903 9 View

Why do I get different FE simulation results each time the solver is run?

Hello, i am performing a highly non linear metal forming simulation using PAMSTAMP FE simulation software. I have noticed that for the same mesh and boundary conditions, I get different results...

01 January 2020 1,074 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

16 November 2018 3,137 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

10 November 2018 8,856 5 View

Can Hedge's correction be run where I have a small sample size but repeated test (ie total output over 11 data points)?

How to run this on SPSS?

17 September 2018 2,519 1 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View