What should be the % of Ti and Sr in the final casting of HPDC ADC6 alloy?

More Dr. Pallavi Deshmukh's questions See All

Are you looking for research collaboration ?

we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]

29 July 2024 6,626 0 View

Dear researchers. pl help how to plot jablonski energy level graph and magnetic hysteresis curve in origin?

through origin software

17 July 2024 4,991 0 View

How is artificial intelligence being utilized to enhance the diagnosis and treatment of sleep apnea?

AI has the potential to improve the management of sleep apnea by personalizing treatment, enhancing diagnostic accuracy, and advancing our understanding of the condition.

03 July 2024 9,393 2 View

Action research design is Quantitative Studies or Qualitative Studies?

14 June 2024 1,684 1 View

Offer or collaboration for book publications?

Dear Profs/ Scientist, if any one is interested or have plan to publish a good quality books/ book edited , I can contribute/help such type of research works . My research...

06 June 2024 5,932 2 View

How to draw SeDeM diagram for preformulation study of drug and excipients?

What is SeDeM expert tool? Is it in silico tool and how to draw the SeDeM diagram for preformulation study? Kindly suggest.

06 June 2024 4,408 0 View

Call of book chapter ?

CALL FOR BOOK CHAPTERS (No Publication Fee) Scrivener Publishing/wiley Dear Prof,Scientist/ experts, Greetings. We are editing the book entitled " FET Devices: Post CMOS Theory and Applications...

28 May 2024 9,284 0 View

Is there a Raising awareness of indigenous medicine among metropolitans?

The growing interest in holistic health practices is leading to increased awareness of indigenous medicine among metropolitan populations. While challenges exist in terms of access and cultural...

09 May 2024 7,041 1 View

Why many times RG is sending email? Is this person is co author or published article? Many times it is been sending.?

Pls dont send many times email is this person is co author or published article? Many times it is been sending. Pls stop it ok

06 May 2024 3,964 3 View

What is the protocol to maintain 260/280 and 260/230 and to get pure DNA from ruminant faeces using Dneasy PowerSoil pro Kit?

I used the Dneasy PowerSoil Pro Kit. But I didn't get a good ratio of 260/280 and 260/230 and didn't get a good band after electrophoresis. I maintain all procedures according to the...

29 April 2024 1,242 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View