What might be the reasons for low assay of a product?

24 October 2017 0 7K Report

In lower strength of a product of BCS class III, we are constantly facing assay problems only in lower strength. Blend uniformity is perfectly fine and higher strength results are also acceptable. Both strengths are dose proportional.

Badges
Science topic

More Zubair Shamsi's questions See All

NO results of PCR infact i have good quantity of RNA ?

I am working HIV. My RNA concentration is 57-65 ng/ul. AFTER cDNA preparation I did not get any PCR result. Only dimer are on the gel. Highly Visible dimers are on gel.

20 February 2024 9,070 3 View

DFT- Free energy calculation of CO2 intermediates using dmol3?

Hi, I am trying to calculate the gibbs free energy of various CO2 intermediates on my catalyst for mechanism development of CO2R. Can anyone please guide me how to perform these calculations to...

16 January 2024 2,657 0 View

My revision of manuscript undergo under-review from with-editor ?

I have submitted my manuscript revision one month ago. after submitting my revision my paper status was (with editor). Now from two, it shows the status of under-review, so what does it mean

19 September 2023 1,735 2 View

Hi.please I need someone to help me to interpret the results ?below.The bps are looking at 109,139,169,199?

Hi. Am currently doing my research study on dengue virus, looking at the four serotypes of dengue virus and also targeting the non structural protein 5 in one step multiplex pcr.

06 September 2023 9,888 2 View

In UDFT optimization, what is the energy order between different spin states of Fe and Co's?

For Fe (Singlet, Triplet, Quintet) and Co (Doublet, Quartet), what is the correct energy order between Fe and Co's spin states in Gaussian after geometry optimization by UDFT?

04 September 2023 8,285 0 View

How I can calculate HOMO and LUMO from .log file from Gaussian? Followings I have used:#P B3LYP/6-31G* Opt Freq Pop=(Regular,NBORead) Density=Current?

I am optimizing complexes and used the following as parameters #P B3LYP/6-31G* Opt Freq Pop=(Regular,NBORead) Density=Current. How I can find HOMO LUMOs in .log file from Gaussian?

16 August 2023 2,088 5 View

LS DYNA define EOS for MAT72R3?

for defining EOS for mat 72R3 I have received an error please help me solve this situation

04 June 2023 6,498 0 View

What are the causes and treatment of bone pain in children 9-12 years old ?

A 9 .5 year-old boy complains of recurrent and frequent attach of bone pain for more than 3 months duration with increasing during the day, not at night, didn't awake him from sleep and increasing...

22 February 2023 5,693 2 View

How to verify the type-II band alignment in 1D/2D heterostructure?

The type of semiconductor heterostructure depends crucially on the alignment of the energy bands at the interface. Semiconductor heterostructures can be classified into three types of...

14 February 2023 308 0 View

Is there any MATLAB and Python code for fetal MRI (gestational age prediction) using deep learning CNN?

I am working on gestational age prediction. I am looking a code to train my network using deep learning techniques such as CNN and CNN architecture.

29 November 2022 1,812 3 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Does Anyone have expertise in in vitro transcription and RNA pull down assay?

I am currently working on LncRNA; to know the lncRNA-protein interactions I want to do RNA pull down assay, so I need to design primers with T7 promoter. I need assistance in this regard.

07 August 2024 6,622 1 View

How to improve plaques in Double Layer Agar Assay?

Hi all! My thesis groupmates and I are working on purifying an E. coli bacteriophage. The phage was handed down to us by the previous thesis group, but they only managed to purify it to about...

06 August 2024 5,801 4 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

How can I find access to heavy metal reference doses from the EPA and WHO websites?

Reference dose and Maximum acceptable concentrations HMs

03 August 2024 8,230 4 View

How to convert g/kg Humic acid dose to kg/ha?

I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?

02 August 2024 7,186 6 View