01 January 2015 3 1K Report

I am working on evolution of microstructure and texture of magnesium based alloys during heavy reduction. I need to know the role of Σ5a ,Σ17a, Σ19a and Σ27a, CSL boundaries in terms of dynamic recrystallization (DRX), static recrystallization SRX, and deformation behavior of magnesium alloys.

More Javed Kamran's questions See All
Which Grade of carbon steel be used as material for storage tanks of sulfuric acid at 99% concentration at 38 °C?

It is reported in literature that carbon steel is generally satisfactory for storage tank for sulfuric acid at or above 98%. Which grade of carbon steel is promising for this purpose?

06 July 2018 5,119 1 View

Why grade A36 carbon steel is not recommended for storage of concentrated sulfuric acid(above 98%)?

Literature recommends that carbon steel is the appropriate material for storage of concentrated sulfuric acid (above 98%) at ambient temperature. But usage of grade A36 as material of construction...

06 July 2018 5,948 4 View

What is the maximum permissible limit of Zinc, Cu, Al, & Sn in AISI 304, & 321 Austenitic stainless steel?

Low melting point metals like Zn, Cu, Al, Sn etc form  intermetallic compounds when present in austenitic stainless steel. Can anyone tell about the maximum permissible limit of these impurities...

03 April 2016 9,876 3 View

What is the possibility and amount of formation of matrensite during cold working at 27 0C, If Md30 temperature for AISI 321 is calculated as 9 0C.

Martensite formation in AISI 321 depends upon the chemical composition, SFE, Md30  temperature and % age  of cold work. The Md30 temperature of  a given AISI 321 steel according to the equation...

03 April 2016 5,930 1 View

What is a good etchant for AISI 321 stainless steel?

which etchant gives good results in order to reveal the microstructure of AISI 321 stainless steel?

03 April 2016 3,227 8 View

What is the effect of Zn, Cu, Al, V, Na & Sn on mechanical properties especially the % elongation of AISI 321 Austenitic stainless steel?

What is the permissible limit of low melting impurities like Zn, Al, Cu, V, Na & Sn in AISI 321 steel. What is the impact of these impurities on mechanical properties of AISI 321 if these...

03 April 2016 7,455 0 View

What could be the reasons of grain coarsening during tensile testing of Mg alloys?

Grain coarsening of a specific magnesium alloy during tensile testing has been observed which not only increased the hardness of the material but very surprisingly the texture got weaker. Please...

31 December 2013 8,929 6 View

Under what conditions during processing of magnesium alloys does the Hall-Petch relation reflect in reverse?

Does the Hall-Petch relation of finer the grain size higher the hardness hold to all Mg alloys? If some Mg alloys show reverse Hall-Petch relation, what could be the reasons?

08 September 2013 6,573 6 View

Similar questions and discussions
Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

How select composition for ods-high entropy alloys?

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close