What is the relation between switching frequency and shoot through duty ratio in z source inverters?

More Prathusah Yerramilli's questions See All

How can I add noise across capacitor voltage in a matlab simulation of grid connected inverters?

It is require to add +2volts of noise to the measured capacitor voltage in the simulation of z source inverter. How can it be added?

26 March 2015 2,813 2 View

How to choose the reference power value in a power control of grid-connected inverters?

It is for closed-loop operation of inverter with PLL for synchronization

24 March 2015 2,609 4 View

What is the exact definition of boosting factor in z source inverter?

Is it the ratio of positive envelop amplitude to carrier signal amplitude? How to give shoot through duty ratio parameter in pulse width modulation technique simulation of z source inverter?

19 March 2015 1,226 3 View

What will be the value of active power if RL series branch is used in simulation of inverter connected to grid?

I simulated z source inverter and connected RL series branch as load with R=10ohm and L= 5mH .Output voltage is 100 and current is 5.I am getting output active power value around 170. But what...

24 February 2015 2,117 2 View

How to simulate z source inverter with capacitor voltage control in matlab?

Please provide simulation model in matlab for the block diagram in the below attached paper,it will be helpfull for my project

10 February 2015 6,456 0 View

Can we separate 1-Acetyl Naphthalene and 2-Acetylnaphthalene using column chromatography?

Acetylation of naphthalene with AlCl3 usually leads to two products(alpha and beta substituted). How can we separate them?.

01 January 1970 1,392 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

Identify the eight key processes of excellent supply chain management and discuss how each of these processes impacts the end customer?

Read the journal article by Douglas M. Lambert, “The Eight Essential Supply Chain Management Processes,” Supply Chain Management Review, Vol. 8, No. 6 (2004), pp. 18-26

04 August 2024 9,919 4 View

Why is nonpoint source pollution potentially more harmful and difference between point and nonpoint sources of water pollution?

01 August 2024 1,180 2 View

How do living organisms play a role in the water cycle and why is nonpoint source pollution potentially more harmful than point source pollution?

01 August 2024 7,061 2 View

How does nonpoint source pollution affect ocean environment & why point source pollution is often easier to manage than nonpoint source pollution?

How does nonpoint source pollution affect the ocean environment and why point source pollution is often easier to manage than nonpoint source pollution?

01 August 2024 8,014 2 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Santosh Sonar

The relationship depends upon the type of switching technique used.Mention the technique .

Prathusah Yerramilli

The technique is simple boost technique implemented for simulation of z source inverter.The requred duty ratio given is 0.35.How to give this value in simulation?

You insert the value of Modulation index as 0.65 for the required duty ratio.All the best.