Python - TRNSYS link not working with Type169?

I used Type169 for data exchange between Python and TRNSYS. Unfortunately, facing the following error. No proper documentation is available for this part. TRNSYS Message 105: A TYPE was called in...

14 February 2021 5,577 1 View

What is the role of ether solvent (such as THF) in Sonogashira coupling?

Can Amine (such as Et3N) be used as solvent as well as base for the Sonogashira Coupling? How to decide the amount of solvent to be used in any reaction? Does the amount of solvent affect the...

14 February 2021 4,018 3 View

Any natural extract (that is easily available) or any drug combination triple which i can use against gram negative?

I'm working on gram negative i want to use any natural extract (plant extract) or triple drug combination against its biofilm formation.

14 February 2021 1,403 3 View

How can i calculate diffusion barrier of Li ion on graphene nanoribon using SIESTA?

I'm a new siesta learner, I'm working on lithium-ion batteries, I have calculated adsorption energy but i am not able to calculate diffusion barrier of Li ion. kindly help me how to calculate...

14 January 2021 2,688 1 View

Suggest some good journals having Impact factor more than 3 which is not an open access one for alternative and complimentary medicine?

Suggest some good journals having Impact factor more than 3 which is not an open access one for alternative and complimentary medicine?

11 January 2021 7,782 1 View

Can I use hcl to adjust ph rather than glacial acetic acid?

In alkaline lysis solution3 acetic acid should be used to adjust pH according to protocol. Can I use hcl instead of glacial acetic acid? Will there be any change in composition of solution?

08 January 2021 7,764 3 View

What is the best method for plasmid dna extraction??

I want to extract plasmid dna from bacterial culture guide me what will be the most appropriate method.

05 January 2021 1,118 14 View

What could be the role of researchers to reduce violence in school?

I want to promote peace and non-violence in school and collaborate for such initiative in future.

30 December 2020 973 3 View

How to reduce liquation cracking in super austenitic stainless steels ?

Super austenitic stainless steel castings showed liquation crack after liquid penetrant testing post heat treatment. How to reduce this in thick walled castings.

26 December 2020 7,959 3 View

Which method is best applied to calculate the crack widths and check the crack control provisions in the super-long post-tensioned concrete slab?

For a super-long post-tensioned concrete slab, in which cracks are especially caused by restraint and predominantly formed by shortening due to shrinkage, creep, and elastic shortening of the slab...

19 November 2020 3,453 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View