i want to simulate a displacement using the hermit interpolation function . idont know exactly the way of this summation .
Maryam
I would guess that you are interested in hermite interpolation. Perhaps searching on "hermite" would help you find the information that you seek.
Jeff
Hallo Madam Ghasemzadeh,
This is simply Tayler series summation. I advice you to see the example in this paper for 3 Node beam:
https://community.dur.ac.uk/charles.augarde/pubs/j1.pdf
Hope this helps
Tamer Qaimari
Its numerical method of interpolating data points as polynomial functions.In this both functions and their first derivatives are assigned at each point of interpolation.Its osculating interpolation type.
whats the displacement equation?
Hi As we know the percent of evaporated water in close cycle cooling towers with indirect heat transfer is less than wet types. I'm going to compare the amount of evaporated water in these towers....
04 May 2018 1,947 6 View
I wanna to calculate the fatigue life of rotational structures, first I need to know their mechanical loads
09 October 2017 9,153 4 View
Hi. As we know the loading in Gas Turbines consist of Temperature Loading and mechanical ladings. Although these two types act simultaneously,I'm about to determine the specifically mechanical...
09 October 2017 1,415 4 View
I'm looking for a source that complitely and explicitly describes meshing techniques, for example sweep or structrual and free in ABAQUS.CAE , its preferd that source comprises some numerical...
10 November 2016 4,176 1 View
im focusing my attention on fatigue analysis in abaqus and infact im new to this section.I am a little confused about related scripting in "Abaqus analysis Manual 6.2.7 overview". It says the...
06 July 2016 1,483 15 View
im trying to calculate the energy that dissipated because of plasticity based on Morrows model and looking for the plasticity model that used there and the data of that. it will be a great help if...
01 January 1970 10,008 1 View
Hi i want to model a beam under cyclic loading and claculate the heat generalized because of plastic deformation. i was wondering if some body help me in this field! with appriciate
01 January 1970 9,056 3 View
i dont know what is the back stress Exactly ? is it only in Creep or there is in every plastic deformation in hystersis loop ?
01 January 1970 7,245 0 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
The paper in question is "Interpolation of Nitrogen Fertilizer Use in Canada from Fertilizer Use Surveys". This paper was very recently published by Agronomy (MDPI). Agronomy has, in the last day...
07 August 2024 9,934 3 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View