PVA fibers are modified with oiling agents to reduce bonding between the fiber and the cementitious matrix.
What is the best type of oiling agent and method of application is most suitable?
Also, how can PVA fiber be tested whether its coated or not
http://iopscience.iop.org/article/10.1088/2053-1591/aaad31/meta
I will like to model the microstructure of concrete/mortar, is there any software to model the resulting products? Thanks
31 December 2018 8,493 2 View
One of the apparatus required for freeze and thaw test according to ASTM C666 is the dynamic testing apparatus. This apparatus is used to obtain the relative dynamic modulus of elasticity and...
11 December 2018 8,747 2 View
I'm looking for software or program suggestions that can be used to carry out data mining and artificial neural network with less programming input.
11 December 2018 5,309 12 View
Non destructive tests equipment for concrete are quite expensive and not readily available. Is there any non destructive test that can be improvised or built with commonly available materials to...
10 November 2018 6,612 4 View
I will like to know why there is always high shrinkage when slag is used at larger percentage replacement of cement. The reasons in terms of its chemical reactions with OPC and the physical and...
10 November 2018 548 3 View
Currently there seem to be no standard that covers how to carry out an accelerated corrosion test for steel in a reinforced cementatious composite. However, several studies have explored different...
10 November 2018 4,972 5 View
The most used fibers for ECC are PVA and PE, however, these fibers are very expensive. Are there other cheaper and greener materials that can be used as fiber in ECC?
10 November 2018 2,951 24 View
The use of supplementary cementitious materials (SCMs) is increasing rapidly as they can be used to partially or totally replace OPC in concrete. The most common types of SCMs are fly ash, slag,...
10 November 2018 6,479 13 View
Engineered cementatious composites are high performance composite and are gaining huge research recently due to their enhanced ductility and durability. What are the major ways to improve the...
10 November 2018 6,868 13 View
I'm using design expert software for the design of the influence of different factors in my experiment. However, I couldn't get any section that shows the percentage contribution of each factor on...
10 November 2018 7,760 3 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,027 0 View
Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...
07 August 2024 8,414 2 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 946 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,545 2 View
Is this circle one of the rings?
03 August 2024 5,987 0 View
I want to know more about petroleum deposits in Iran.
02 August 2024 8,725 3 View
Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?
01 August 2024 7,503 2 View
I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...
01 August 2024 8,753 2 View
Hi all, may I ask you for advice about treating monolayer culture cell line with essential oil. Due to the hydrophobic character of the oil, I am concerning how can it equally affect to all the...
31 July 2024 5,301 2 View
What is the thermal expansion coefficient of human muscle?
27 July 2024 7,190 0 View