How to do mono formylation of N,N-diethyl-3-methoxybenzamide?

I have attempted the formylation of the above mentioned compound using a very well reported protocol using secondary Butyl Lithium and TMEDA at - 78 degrees Celsius. I have done it quite a few...

08 February 2021 2,793 2 View

What is the minimum number of cells required for fluorescence in situ hybridization?

I have to perform a FISH experiment with limited number of cells and I am trying to estimate the minimum number of cells required to do FISH. Cells are from mammalian cell line. I failed in doing...

12 January 2021 7,887 1 View

Can you give me some Information about the generation of ROS in marine surface water?

Reactive oxygen species is a very new term i think

23 December 2020 8,416 4 View

Can someone suggest me a wear detection method for a pipe which goes under intense heat and pressure at intervals?

I am looking for a wear detection method for a pipe that goes under intense heat and pressure for short instances at intervals. this process has an average cooldown time of 8 seconds between each...

08 October 2020 3,776 2 View

Single-cell cloning from SkBr3?

Did anyone tried single-cell cloning from SkBr3 cell line. I am failing in growing cells post single cell seeding in wells. Any help is appreciated

27 September 2020 8,762 4 View

What to do when RT PCR becomes positive again after 15-20 days of 1st sample positivity?

We are getting some patients who were initially positive of RT PCR for Covid. But in retesting after 15-20 days or even 20 days after those patients remain still positive. Is it for dead RNA...

17 August 2020 9,552 9 View

How to calculate % sequence identity using Clustal W?

I am calculating % epitope conservation for different mammalian antibodies against zebrafish. I have performed the Clustal W for antigenic peptide used in raising the antibodies against the...

05 August 2020 6,399 5 View

What is the Source of Harmonic Power ?

Consider a sinusoidal supply at fundamental frequency as shown, with a series inductive reactance leading to a bus. Let a diode rectifier load be connected to the bus. The switch Sw for resistive...

24 June 2020 8,175 27 View

What is the best book on Game theory from the perspective of Computer Science and Engineering?

I do not know much about game theory. I am finding a book where different protocols and algorithms of computer science have been analyzed using the concept of game theory.

17 May 2020 4,774 7 View

How can a PhD in interdisciplinary fields can benefit a researcher in job market?

I am a PhD scholar of Humanities and my research is broadly connected to Anthropological studies and framework. I have also published with an Anthropological journal of global repute and looking...

10 May 2020 4,202 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View