What are the primary conditions for simulating distributed power generating units?

More Vivekanandan Kandiannan's questions See All

What happens to three phase motor... when a phase is reversed in three phase power supply?

If a power is reversed in three phase supply, what will happen to the motor if they are connected.

04 May 2016 3,572 4 View

Can anyone suggest the book to learn about PWM generation using PIC controllers?

I would like to learn the PWM generation using micro controllers. I request you to suggest easy method to learn about it.

10 November 2015 1,484 1 View

Can any recommend me a best electrical software(freeware) to draw electric circuits?

I need to draw some electrical/electronics circuits, so am i in search of free software to draw a perfect circuits.

09 October 2015 6,900 2 View

How do I perform harmonics reduction?

I would like to work on harmonic reduction, using matlab. So, please give me some information on it, how to work on it.

02 March 2015 2,313 5 View

What are the environmental effects of solar power plant?

I have heard that solar panels emits cadmium that causes cancer in humans and some other environmental problems.

04 May 2014 2,829 9 View

What are the available techniques to operate smart grids?

How can smart grids be operated and how does the operation work?

02 March 2014 5,884 4 View

During Integration of renewable energies, what are the factors to be considered?

When we develop a distributed grid using renewable energies, what are factors to be considered when they are coupled together, and what kind of controls can be used to integrate the sources such...

01 February 2014 4,126 6 View

What is a free international electronic journal for publishing studies and projects regarding smart grid technology, distributed power generation?

Ideally, with a good impact factor?

31 December 2013 7,547 2 View

How does one measure the peak(rms or average) values of voltage waveform for calculations in MATLAB?

We get a sinewave form in matlab to calculate the voltage, but I need only the peak(rms or average) values of it. I need to find the voltage value as like in practicals using multimeter.

09 October 2013 4,253 18 View

How to operate circuit breaker during fault condition on MATLAB?

When we are simulating the fault on power systems, using MATLAB, how to operate the circuit breakers by providing external signal after the fault is developed?

08 September 2013 1,166 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Are there any good simple systems or platforms to recommend?

In order to show people the beauty of control and enhance enthusiasm for learning control theories, are there any good simple systems or platforms to recommend?

05 August 2024 10,034 1 View

In what part of the brain´s rabbit bdnf is located and include references please?

I´ve been unable to find specific information about this neurotrophin in the CNS of rabbits exclusively. There is extensive info in mice, fish and rats, but in brain´s rabbit is hard to find....

04 August 2024 762 1 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Marta Poncela

What is the aim of your simulation?. Because the assumptions in your model depend on the aim of your work

Vivekanandan Kandiannan

@Marta Poncela: My simulation is based on energy management system

Sergey Ostroumov

Dear Vivekanandan,

I think, you need to take into account current direction. Since there are many power sources, one can affect another because of the wrong current direction. The simplest solution is to put a diode so that the current flow in the predefined direction.

Thanx Sergey, I dint think about the usage of diode for detection of current direction, now am getting idea for it.