How can I calculate the average size for Au NPs fro UV/Vis spectroscopy only, without TEM?

How can I calculate the average size for Au NPs fro UV/Vis spectroscopy only, without TEM?

31 December 2015 921 4 View

Is there a difference in the crystal structure for bulk gold and gold nanoparticles such as in X-ray diffraction pattern and position of EDX?

Is there a difference in the crystal structure for bulk gold and gold nanoparticles such as in X-ray diffraction pattern and position of EDX?

11 December 2015 7,679 6 View

The attached link may be help you alot?

http://www.sciencedirect.com/science/article/pii/S0921452616303842

01 January 1970 8,916 2 View

For semicrystalline polymer in DC conductivity, the electrical resistivity increased with increasing temperature until Tg decreased after that why?

For a semicrystalline polymer in DC conductivity, the electrical resistivity increased with increasing temperature until Tg and decreased after that temperature?

01 January 1970 5,953 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How to indicate the degree of litter decomposed by microbes?

Any technique could detect the degree of litter decomposed by microbes? Or any indexes could do this job? I want to split the contribution of microbes during decomposition, so any suggestions...

23 February 2021 1,362 5 View