What are the parameters that influence the process of DEM generation from a Cartosat-1 stereo image?

04 April 2014 1 787 Report

I am using multiple Cartosat-1 stereo images for generating DEM. I want to know how to choose the ground control point location to get an accurate DEM. I have generated the DEM using software LPS 9.1. DEM gives very negative values at some locations in spite of providing ground control points at those location.

Marco Gianinetto

You should check the parameters’ used for the data processing. Maybe the image matching failed to detect correct homologous points (or never found homologous points at all) where you have negative values.

Badges
Science topic

More Prachi Pratyasha Jena's questions See All

Is it appropriate to use surface reflectance value in NIR band for flood water delineation ?

I am using MODIS surface reflectance product (250m spatial resolution, 8 day composite) which comprises two bands: one is visible band and another is NIR Band. Is it appropriate to use NIR band...

31 December 2014 1,252 2 View

What is the approximate cost of acquiring and processing LiDAR elevation data per square mile?

I want to know the total cost of acquiring and processing LiDAR elevation data. I have seen in many articles that the cost per miles is reduced with increase in surveyed area. Does the cost vary...

10 November 2014 6,366 4 View

Do MODIS -Terra and -Aqua images differ in providing results of flood extents?

06 July 2014 4,490 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

Which SAR dataset to use for generating coherency matrix and performing target decomposition (Description) ?

Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...

02 March 2021 8,481 3 View

Where i will get the Desmodium and Napier grass seeds?

26 February 2021 975 4 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Are there methods for automatically mapping floodplains, fans and terraces?

I want to map these river geoforms with as little subjectivity as possible. I have a high resolution DEM generated by drone data.

22 February 2021 7,800 3 View

Covid 19 Pandemic ' impact on digital transformation?

Covid 19 Pandemic and digital transformation

22 February 2021 3,351 5 View