How to convert 2D stack images to 3D to obtain surface area of nucleus?

I have 15 slices of the nucleus at different z-heights from confocal imaging. I would like to use these slices to reconstruct the 3D nucleus and ultimately estimate the surface area of the...

20 February 2021 6,967 1 View

How to tackle "CONSTRAINT CONTROLS" error while using tie between CFRP and frame segment in abaqus?

Hello, I had been trying to model a portal frame wrapped with CFRP in ABAQUS. To tie the CFRP laminates with frame I need to use slave/master surface interaction. But whenever I try to model the...

19 January 2021 2,906 3 View

What to do if I am doing a Meta Analysis of Exploratory studies and the studies do not have effect size??

I am doing a meta analysis of imaging exploratory studies which themselves did not have effect size. Therefore, I am unable to compute the variability in the effect sizes in my meta analysis. What...

18 January 2021 4,881 4 View

I want to convert Methane gas to liquid Methanol using photocatalysis. Can you please suggest me a good paper which I can study ?

There are a number of publications regarding this, but none of them are clear and show the mechanism of gaseous Methane conversion to liquid Methanol.

06 January 2021 364 3 View

Can wavelet packet sub-bands be stacked together to form an image?

I have a 1D signal and I have done wavelet packet decomposition on it which is giving several sub-bands. Can I stack these sub-bands (one below other) to form a 2D matrix and hence an image...

27 November 2020 1,269 5 View

How can I maintain a surface at isothermal condition, say at 300 deg Celsius.?

I have 6 heaters each of power 0.5 kW and mounted below a curved mild steel sheet of thickness 4 mm. The heaters and the below section is covered and insulated. I want the top surface to be...

05 November 2020 199 5 View

what are the possible reasons for Crop Water Stress Index values higher than 1 under moisture stress condition?

I have determined CWSI using the theoretical approach of Jackson et al., (1982) based on canopy temperature measurement in chickpea. at the final stages of crop growth some of my values of CWSI...

28 October 2020 9,992 3 View

Will there be effect of around 4wt % B2O3 in ladle slag on refractory erosion?

The effect of B2O3 additions on CaO-MgO-SiO2-Al2O3 based slag/flux was studied by many researchers. B2O3 addition helps in lowering the viscosity of slag which helps in eliminating the sticking of...

28 October 2020 6,722 6 View

Do always a Good paper depends on How much Citations it Received. I have seen many Good Research Papers with zero or less Than 10 Citations?

Its a Research Paper related Question

22 October 2020 6,179 4 View

Help in cloning, should I create 5' phosphate group on digested vector?

Hello all, I am trying to introduce an annealed DNA fragment into the double digested vector. The ssDNAs were ordered without a phosphate group modification. The vector is digested with XhoI and...

20 October 2020 8,357 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View