What are differences in specifications for Martensite transformation in ceramics comparing to metals?

Fatemeh Sadat Sayyedan @Fatemeh_Sadat_Sayyedan

12 December 2014 1 1K Report

I just know about Martensite transformation in metals. For example, these transformations are thermal and diffusionless. Also, the kinetic and morphology are dominant by strain energy.

Mohammad Shirdel

Hi, There are many articles on your mentioned topic. However, I direct your attention toward the following article:

http://www.sciencedirect.com/science/article/pii/S0079642500000050

Badges
Science topic

More Fatemeh Sadat Sayyedan's questions See All

What is the best pre-treatment to active the glass surface for sol-gel dip coating?

I am trying to dip coat a glass into the sol-gel derived solution. But, the sufficient adhesion is not achieved after drying and annealing. What is the best pre-treatment to active the glass...

07 August 2019 3,677 3 View

What method is used for measuring ZrO2 thermal sprayed coating?

01 February 2015 5,356 4 View

What is the hardness of Ni3Al?

Ni3Al is an inter metallic compound.

31 December 2014 4,834 4 View

How can we synthesize amorphous materials by sol-gel?

11 December 2014 7,598 2 View

Why does stacking of fault energy increase with temperature in F.C.C crystals and decrease with temperature in H.C.P crystals?

Why does stacking fault energy increase with temperature in F.C.C crystals and decrease with temperature in H.C.P crystals?

11 December 2014 7,983 2 View

What is the driving force for growth of the particles with the same size in the matrix?

what is the driving force for growth of the particles with the same size in the matrix

11 December 2014 1,201 4 View

Does the protective layer Al2O3 form on the surface of aluminium alloys (such as Al-Zr) like pure aluminium?

Does the protective layer Al2O3 form on the surface of aluminium alloys (such as Al-Zr) like pure aluminium

11 December 2014 6,641 6 View

What is the difference between short range order = 0 and long range order = 0 in disordered alloys?

What is the difference between short range order = 0 and long range order = 0 in disordered alloys

11 December 2014 9,839 8 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

How to back transform the results generated from analyses using log transformed with In(X+1) data?

I am conducting my analysis using SPSS. I log transformed my data using In(X+1) as my data contain zero values. However, when I want to back transform the regression coefficients generated from my...

31 July 2024 7,860 3 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Does it exist some special technique for cutting ceramic membranes for Cross-sectional FESEM images?

Does it exist some special technique for cutting ceramic membranes for Cross-sectional FESEM or SEM images?

25 July 2024 5,482 2 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Swerling Characteristic functions?

Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...

23 July 2024 4,925 1 View

Radar Detection Probabilities?

Currently I need to calculate detection probabilities (PD) from RCS data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0 Equation. The idea is based on...

22 July 2024 2,851 0 View

Pink bacterial colonies?

I am cloning an overexpression plasmid with my protein of interest tagged with mScarlet. After transforming my ligated product into DH5α bacteria and plating on LB agar, I noticed colonies with a...

22 July 2024 5,953 6 View

Radar Detection Probabilities using beta distributed Scattering Cross section?

Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...

22 July 2024 868 0 View