Can anyone please help me in processing SAR SLC data to generate interferogram using SNAP?

I have two scenes of the study area, one top and the other bottom. As per the tutorials and papers published, the step include coregistering the master sand slave images. However, when i try to...

24 February 2021 6,372 1 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

How can we find crop transpiration (Tr) value from ETo values in Aquacrop model?

it like how we can get Tr value separately from ETo values in Aquacrop

20 December 2020 5,817 3 View

How to find load / force acting on the top face in ansys workbench?

The image attached is the representation of my application. This is an assembly of three items (top plate, bottom plate and the 5 load cells). The bottom plate is fixed and a load of 40 Kg is...

15 December 2020 1,145 6 View

Unlikely condition in the water inundation area after the cyclone?

I have done flood mapping with Sentinel 1 data for 3 districts of India (West Bengal) i.e. North Pargana, South pargana and East Medinipur. North and South Pargana are showing increasing trend in...

11 December 2020 4,714 3 View

How to calculate Area-Weighted Average Temperature at outlet in Ansys?

Suppose a fluid is flowing between two parallel plates (and exchanging heat) for 100-time steps. So, there is an area-weighted Average temperature at every 10 steps. How can I write a UDF to...

29 November 2020 6,240 2 View

Can you please recommend articles or book for in depth cocrystal information?

I am looking for information about coformer screenig, feasible method of synthesis at laboratory scale, cocrystal screening, solubility study, Dissolution study of powders, FT-IR analysis, DSC...

10 November 2020 413 6 View

How to know from DSC thermogram that cocrystals are formed or not?

I got three endotherms after doing DSC of physical mixture of Drug and coformer what this Indicate?

06 October 2020 350 4 View

What is apparent Km Value of an Enzyme, Is it different from usual Km value and Why it is important?

It is very much confusing when some papers use this term "apparent Km of an enzyme even if they use single substrate ? Not at all clear ! Please help me understanding this. Thanks in advance.

27 September 2020 3,522 7 View

What are the different revese crosslinking protocols?

I need to crosslink my cells for my experiment and at the end, I need to reverse crosslink and extract the proteins. Can anyone tell me what protocols are there for reverse crosslinking after...

23 July 2020 6,257 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

What are the popular techniques for pre-processing measurement data in Smart Grid/Power System?

The data collected from various measurement devices often contains erroneous values - such as noise, missing values, etc. What are the popular techniques for pre-processing measurement data in...

14 February 2021 4,642 2 View

What can I do to keep magnetic beads suspended in solution within a syringe?

I'm looking for ways to prevent the settling of magnetic beads in solution. I have been using a syringe pump to inject a suspension of magnetic beads in PBS into a microfluidic device, and so far...

09 February 2021 6,206 2 View