The output of a certain voltage divider is 12 V with no load. When a load is connected, the output voltage.?

More Mohammad Nikkhou's questions See All

How to be defined an event in DSL?

DSL:Digsilent Simulation Language The DSL language provides procedures for the generation of an interrupt event and for sending messages to the output window

31 December 2016 6,674 3 View

I want to get some information (e.g thesis) about the impact of distributed generators in the sub transmotion?

the impact of distributed generation on the reliability and stability?

04 May 2016 9,368 11 View

The best resourse for learning the dynamics of power systems to prepare a Ph.D.?

Introducing resources؟ Test resources؟

01 February 2016 8,456 7 View

What is the input port power of a cell phone antenna?

06 July 2015 6,612 5 View

What is the method of improving the power factor?

06 July 2015 5,754 10 View

How to Calculate the Suitable Capacitor Size in Farads & kVAR for Power factor Improvement?

05 June 2015 6,834 4 View

What is the difference between AC and DC Resistance & How to calculate it?

05 June 2015 4,470 7 View

Which of the following is not a type of energy source?

A. generator B. rheostat C. solar cell D. battery

04 May 2015 8,480 8 View

How to Calculate/Find the Rating of Transformer in kVA (Single Phase and Three Phase)?

04 May 2015 4,336 4 View

In a series resonant band-pass filter, a lower value of Q results in...؟

04 May 2015 7,381 3 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,627 1 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

I need to connect expert in Urban design for Health ?

I studying PhD course in Urban design for Health. I need to know in some fileds: residental block, green open space and Transport TOD. I need connect with expert in that fileds.

14 July 2024 1,892 3 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Language teachers can develop speaking skill through listening practices. Can you please suggest some more ways to promote the same (Speaking Skill)?

"Today several adjectival phrases have been used to describe English like ‘International Language’, ‘Lingua-Franca’, ‘Language for Globally Connecting’, ‘Library Language’, ‘Official Language’,...

01 July 2024 8,406 5 View

Can I connect my ResearchGate account to LinkedIn?

Sharing research simultaneously on both platforms

28 June 2024 9,120 2 View

Self discharge of freshly made NMC half cells and voltage stabilizes at 3.3-3.5 V vs Li/Li+ during charging. What can affect it?

I am making Li half cells using NMC as cathode. The OCV is around 3 V but it self discharges and during charging the voltage increases to 3.5 V and then drops to 3.3-3.4 V and stays there. I have...

23 June 2024 842 3 View

How to predict the efficiency of a very low speed Railgun Actuator/Lorentz Force Actuator?

I'm not an electrical engineer or anything related to that subject, so my apologies if I understood something incorrectly. Well, I read somewhere that the slower the railgun is, the higher its...

23 June 2024 1,082 0 View