the field of single energy dimension or natural power or arrival of big black hole how occurred? What were in the past of big black hole?

Shahidur Rahman Sikder @Shahidur_Rahman_Sikder2

02 February 2018 0 9K Report

Where did the universe come from? As a result of the present situation, it became possible to find out the correct solutions to the questions about Universe creation or creator through that 21st century of discovered fundamental Universal Rule and evolution revolution of physics. Possibility, swiftly finds out most important answering of the questions to help people find a place and their role of the Universe. Universal Rule at www.universalrule.info

https://shahidurrahmansikder.wordpress.com

In this circumstance, a question may be arisen that the field of single energy dimension or natural power or arrival of big black hole how occurred? What were in the past of big black hole?

Badges
Science topic

Similar topics
Correction

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View