Some info about comsol multiphysics

More Denis Ermolaev's questions See All

Which module of Fluid Flow in Comsol I can use for Modeling of Viscous Fingering?

Could you tell me which module of Comsol Multiphysics should I choose for simulation of the motion of the interface between two liquids? Exactly - which module of Fluid Flow I can use for Modeling...

31 December 2017 460 3 View

Hello! Could you tell me which module of Comsol Multiphysics should I choose for simulation of the motion of the interface between two liquids?

Could you tell me which module of Comsol Multiphysics should I choose for simulation of the motion of the interface between two liquids?

31 December 2017 7,671 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Hadi Parsamehr

If you wanna simulate gas sensor, it is the density of gas volume. also you can find this kind of structure in COMSOL Manual.

Denis Ermolaev

Thank you for the answer. I simulate the gasification process, and there have two volume - gas volume and reactor volume, so was difficult about this. In the manual value mol/m3 have indefinite meaning, that is why was a question.