How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Submission of the Materials Studio jobs to the remote Linux cluster?

I am doing some simulations using the Forcite module in Materials Studio. As the speed of this calculation on my workstation computer is unacceptably slow, I am trying to submit my job to the...

14 January 2021 8,653 1 View

Installing CASTEP on Windows10 using Cygwin?

I am trying to install CASTEP on windows 10 using cygwin but no success did anyone do this before? Thank you

05 October 2020 7,320 3 View

Is there any way to separete the band at H point in the following picture?

Its a band structure of germanium where I see CB and VB are connected through H to K points. I want them to be connected only in one high symmetry point. What are the parameters I need to change...

25 September 2020 9,413 3 View

Is it possible to run a doped system in CASTEP without creating supercell structure?

I was run a doped system in CASTEP without supercell and it was successfully optimized. But, I am not fully understood when I have to create a supercell. The unit cell I had used contain 28...

06 July 2020 7,657 2 View

How can I model & simulate quantum dote thin films using CASTEP with different tail parameters?

A QDSC solar cell design that uses quantum dots as the absorbing photovoltaic material. It attempts to replace bulk materials such as Si, CIGS, CdTe ... etc. Quantum dots have bandgaps that are...

16 March 2020 1,986 4 View

How can deposit a molecule on graphene by CASTEP ?

I want to know the stages of depositing a molecule on the surface of graphene with a CASTEP

01 February 2020 10,014 1 View

How can I do the Magnetic calculations using CASTEP code as ferromagnetic system , anti-ferromagnetic system ?

with a CASTEP

01 February 2020 1,612 4 View

How to Change Pressure and Temperature In CASTEP?

Seniors please guide me how can I change the pressure or temperature in castep.. I want to calculate the band gap by changing of pressure (temperature)...

04 May 2019 8,565 5 View

Can someone please help with calculating the Cohesion energy and Ethalpy of formation?

Dear CASTEP users, I want to determine the chemical stability of the alloy I model using CASTEP by calculating the cohesion energy and the enthalpy of formation from the data calculated. I used...

03 April 2019 9,260 2 View

Which software can visualize the NMR tensor with three arrows?

Dear colleague: I have calculated the NMR chemical shift by CASTEP, and then I want to analyze the NMR tensor of some atoms in my structures, I can visualize it by magresview with...

28 January 2019 6,388 3 View