How to perform Cox proportional hazard analysis or Kaplan-meier survival analysis in SPSS?

At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...

15 February 2021 9,145 2 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

For acid treated montmorillonite clays what will be the result of surface area?

The organo montmorillonite nanoclays modified with octadecylamine were used for the experiment. After acid treatment, the surface area will be increase. However, in my experiment, the surface area...

10 February 2021 1,581 3 View

How to identify when a gaussian program is about terminate normally?

Dear all, I am trying to optimize a bimetallic complex using # opt=tight b3lyp/lanl2dz scf=qc geom=connectivity. The program is running for around 5 days but the size of the .chk remains same...

05 February 2021 8,721 3 View

Can I use 500ng of DNA for restriction digestion?

The recommended amount of DNA for restriction digestion is 1ug in a 50ul rx I've got around 500-600ng of DNA in a total volume of 35ul. Would I get satisfactory results with this amount of DNA for...

31 January 2021 729 6 View

What is the effectiveness of online teaching during COVID-19?

Please share your experience on the effectiveness or challenges on online teaching during Covid-19 lock down. Share your experience about challenges, technology, online learning platform,...

26 January 2021 4,532 37 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

LC-MS metabolomics data after annotation some have their compound name but no KEGG id or with KEGG id but no pathway. How to interprete?

Recently I have generated LC-MS metabolomics data. After annotation, some have their compound name but either no KEGG id or KEGG id but no pathway. How to interpret those compounds? Additionally,...

18 January 2021 1,938 3 View

Has there been any scholarly research done in schools that addresses teaching from a global citizenship perspective to deal with global problems?

The current global pandemic, the climate crisis, the destruction of the oceans (with plastics, etc), and massive numbers of refugees are part of a set of serious global problems. It is clear...

13 January 2021 2,022 3 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View