Need Al-Li alloy....

More Kishore Kumar.M's questions See All

I am using solartron 1260 FRA for impedance anaysis of ceramics. I am getting inductance effects at high frequencies. How to correct this?

I came to know that this effect can be corrected using a short circuit measurement. How to do this measurement? Are there any other ways to mitigate this problem? All measurements we made showed...

01 February 2018 3,102 3 View

I am running NEB calculation in MedeA VASP for a 1x1x5 supercell. I have got activation barrier as 67 kJ/mol /cell. How to extrapolate to 873 K?

Firstly I wanted to know if the value is for entire supercell or a single unit cell. Secondly the activation barrier is calculated at 0 K. how to extrapolate this value to 1073 K ? Please let me...

03 April 2016 9,360 0 View

What thin films we can use as electrolyte in fuel cells?

Energy

08 September 2014 2,842 7 View

Does anyone know where to get Cu-Cr-Zr alloy sheet in India?

A sheet of thickness 2 mm.

06 July 2014 8,795 5 View

Has any manufacturing technique lead to change in electrical properties of metals thereby increasing its electrical conductivity?

11 December 2013 1,465 2 View

Nickel nanoparticles

I am in need of nickel nanoparticles 1nm in size. Can anyone recommend a synthesis procedure or a company from which to buy them?

05 June 2012 5,981 17 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View