Longitudinal heat conduction in Regenerators ?

More Easwaran Krishnan's questions See All

Suitable materials for orifice plate?

Does the construction materials have any influence on accuracy of orifice flow meter? ( Working fluid: air)

09 October 2018 1,933 1 View

Thermistors or Thermocouples for transient measurements?

Does a thermistor respond faster than thermocouple? Will it gives a more accurate reading during transient temperature measurements?

03 April 2018 7,713 5 View

Parameters affects on freezing and melting time of a substance

What are the major parameters that depends on freezing and melting time of water- ice, also the melting as well as freezing time of water- ice phase transition requires same time? Please share...

31 December 2015 5,434 2 View

Maximum actual Efficiency of a n ORC ?

Is it possible to achieve more than 15 % of thermal efficiency (not Carnot)for an ORC working with Waste heat (as source of heat)?

31 December 2015 8,055 4 View

Water from Atmosphere

Utilizing a cooling coil for recovering water from air is an effective method ? (Relative humidity almost 70%) ,Please share the relevance/scope or experience about this.

11 December 2015 5,808 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Seeking recommendations for equipment to mimic sunlight and heat up a greenhouse system?m?

I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...

28 July 2024 4,006 2 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Can anyone kindly suggest research topics in the area of thermodynamics, heat transfer, fluid mechanics or renewable energy?

I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....

24 July 2024 4,058 5 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How Can I Resolve a Persistent Unwanted NMR Peak at 1.25 ppm?

Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...

15 July 2024 9,065 4 View