LET Failure on 1120 MFD CAPACITOR?

Babita Nanda Panigrahy @Babita-Panigrahy

20 July 2024 0 5K Report

Dielectric failure is there during manufacturing process. i have investigated metallization process. Kindly help me the solution ,

capacitance has huge drop ,

Request for your guidance

Badges
Science topic

More Babita Nanda Panigrahy's questions See All

What are the procedure to test DC/DC Converter for 30kw,1000i/p, 200-800v o/p?

In industry how to do testing on DC TO DC Converter. kindly suggest

22 November 2023 3,172 2 View

Can i get the information of weight of inductor for below spec?

Inductance: 220uH DC Current: 400A Ripple Current: 20% of DC Switching Frequency: >20kHz Loss: as low as possible for 200V operation, the inductance will be less. However, we need to keep the...

09 October 2023 7,658 0 View

How to design 18.2KV HF Transformer?

Kindly help me to design 18.2KVA High frequency Transformer.

29 August 2023 4,011 1 View

PQ32-30 core. Please also find an opportunity to reduce the size further without impairing the performance.?

How can reduce the size of high frequency transformer ?kindly guide

06 June 2023 814 1 View

240W LLC transformer whose design details are as below Operating frequency - 250 kHz Total loss < 1.5W full load No load loss < 10 mW Turns ratio ?

For PQ32-30 core. How to reduce the size further without impairing the performance.

21 May 2023 7,403 0 View

How to decide wire gauge and number of turns for designing of 300WSMPS?

300W SMPS Input CMC RMS Current=3A 30mmx15mmx25mm Input DMC RMS Current=3A 26mmx14mmx25mm Output CMC RMS Current=25A 20mmx12mmx25mmcore is ferrite core, Inductance of Input CMC is 7mH, Input...

02 May 2023 1,885 2 View

Can anyone suggest me how to use nitrogen gas and setup kit in muffle furnace for biochar preparation?

hello, I am conducting a research on biochar. But am in initial phase. I came to know that nitrogen use is important in biochar preparation for pyrolysis. Thus I need suggestion and help regarding...

25 January 2022 2,758 4 View

How to visualize CHGCAR file of VASP in VESTA?

In vesta, I am not able to visualize CHGCAR file created by vasp. As I try to open it, the vesta window turns grey. kindly help

23 March 2020 1,414 7 View

What is the future scope of studying multiferroicity in oxides?

What has been done so far...

19 June 2018 5,900 3 View

Primers for HIV drug resistance?

please let me the primers for HIV drug resistance.

14 January 2017 2,813 3 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How to make the concentration measurements for the hydrogen absorption/desorption in the metal hydride?

Hello Everyone! I am trying to create a metal hydride system where I am trying to create a temperature control with the emphasis on measuring the concentration of the hydrogen with the hydrogen...

29 July 2024 7,577 2 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How can biogenic synthesis techniques be applied to develop plants capable of extracting and processing heavy metals from contaminated soil, and wha?

Understand how to utilize biosynthesis to develop natural and sustainable solutions to address heavy metal pollution and improve environmental and agricultural conditions.

26 July 2024 1,469 1 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

Does post-translational protein modification cause devisions on observed pI verses calculated pI?

In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....

24 July 2024 8,076 3 View