I am looking some research works on high temperature application of basalt fiber in combination with thermoset or thermoplast polymers.
Hi,
You can find some effects of temperature (at 313 K and 333 K) on properties and strength of basalt fiber reinforced polymers there:
http://cdn.intechopen.com/pdfs/38408/InTech-Properties_of_basalt_plastics_and_of_composites_reinforced_by_hybrid_fibers_in_operating_conditions.pdf
Here is another paper on this subject. I can send you this paper if needed.
I'm going to simulate the structural response of a sandwich structure with agglomerated cork core under bending and compression loading. Is there any reliable information about the structural...
07 August 2019 9,939 1 View
Hi, I'm looking for a comprehensive study to novel polymer matrix composites.
11 December 2018 901 2 View
I'm trying to define the water absorption of polymeric composites in Ansys/Abaqus. The problem I don't know is what should be considered in this regard?
09 October 2018 2,046 2 View
Matrix and fiber/matrix interface degrade due to water absorption. Please suggest the possible methods to prevent such degradation by using additive materials such as nano-particles.
09 October 2018 9,196 0 View
I want to define a proper damage criteria for balsa wood in Ansys in a simple way.
01 February 2017 6,153 0 View
01 February 2017 852 0 View
I am trying to create the proper bond between a thin plate of aluminum 5083 and glass fiber reinforced polyester, but after a while, delamination occurs
31 December 2014 7,230 6 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 435 3 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View