Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

What is the difference between PBE and PBEsol functional?

Hello, I am a 3rd year chemistry student and I'm writing my project report on computational chemistry. does anyone know how PBEsol improves upon the PBE functional? Thanks in advance

19 February 2021 7,068 4 View

Can someone help me with this error that I am getting while estimating a VAR model in R?

I am using annual time series data to estimate a VAR model in R. However, when I run the command to find the optimal lag length, I get the following error: Fehler in VARselect(data, lag.max = 10,...

18 February 2021 9,647 3 View

How to avoid ATP degradation while performing ATP assay?

I am using the ATP Assay Kit (Colorimetric/Fluorometric) (ab83355) for measuring intracellular ATP from treated cell lines. Although my standards are wokring fine when using the fluorometric...

15 February 2021 3,746 4 View

In your experience what is the difference between G.652D and G.655D optical fiber. In field and in lab?

In our current era there is a big confusion about the usage of G.652 and G.655 optical fiber cable. Theoretically G.655 is much better than G.652 but the operator feel that G.652 is giving almost...

11 February 2021 4,006 8 View

How many dilutions are good enough for TCOD50 of SARS-CoV-2?

I started with 10e-1 till 10e-10. But when I searched for online calculator they mostly consider 5 dilutions. Is there a reason behind it or I should make less dilutions?

11 February 2021 5,839 3 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How to dissolve cross-linked Amberlite IRC120 H, hydrogen form resin?

Hello all, I have used Amberlite IRC120 H, hydrogen form acidic cation-exchange resin for the ion-exchange of waterglass [sodium silicate solution -- 40% Sodium silicate (mol ratio > 3.2)...

21 February 2021 5,614 3 View

How to calculate stress at the cross section of spherical particles within a matrix?

Hi all, I am currently working on some background calculations before I start a new project related to metal matrix particulate composites. I am trying to find a way to calculate the stress at...

19 February 2021 8,503 3 View

Onset of Photo Oxidation in Polymers?

Hi! I am looking for some specific information in regards to the minimum amount of UV intensity required to begin the photo degradation process in polymers. I understand each polymer is...

15 February 2021 7,703 4 View