Which peak should I consider when calculating ZIF-8's crystalline size from XRD?

Hello, Using the Scherrer's equation, one could calculate, roughly, the crystalline size of ZIF-8. However, I am confused as to which peak in the XRD pattern should be taken for the calculation?...

10 January 2021 8,633 3 View

Amorphous XRD Data?

Dear colleagues, I analyzed my material using XRD analysis and the material has shown amorphous behavior , how can I specify the composition of the material is there any extra analysis I can...

24 December 2020 1,280 10 View

Why does a Nested PCR protocol amplify samples and not amplify positive control?

I have this problem. Today I used a new positive control of an isolated NC-1 strain in cell culture and the problem persists. I performed a serial dilution test to test the sensitivity of the...

08 December 2020 6,252 2 View

How to avoid the formation of traces and dimers in DNA gel electrophoresis?

07 December 2020 3,052 3 View

Is the pipetting order of the positive and negative controls in the PCR important to avoid in a possible contamination?

I have been watching bands form on my negative controls. I have already changed all reagents, optimized the hygiene of materials and the environment and increased care in pipetting.

07 December 2020 9,090 3 View

How to standardize and obtain a good PCR reaction with samples with a low and variable amount of DNA?

I work with the detection of N. caninum DNA in milk samples in milk samples. The DNA concentrations in my samples range between 2-90 ng / ul. I would like to establish and standardize a final...

01 December 2020 8,792 3 View

Can anyone help me regarding the doubling time of JAWS II cells?

Anyone with experience in growing JAWS II cells could give me an idea of its doubling time? I intend to use these cells for transfection protocols. Any tips to help with growing and transfecting...

01 December 2020 855 3 View

How to know if 87Sr/86Sr is reliable for Sr isotope chemostratigraphy in marbles?

I am currently looking for parameters to know if 87Sr/86Sr data is reliable for chemostratigrahy in marbles, and/or parameters to know if those marbles have had some post-depositional...

30 November 2020 9,032 8 View

What are the scaling parameters in the field of gas turbine combustors?

We have an optically accessible atmospheric combustor. We want to perform the instability analysis of the combustor like flashback, blowout and instabilities occurring near lean blowout. We are...

25 October 2020 2,235 1 View

Genome sequenced twice in the same technology are very different. How to explain?

Hi dear all, We are studying a fungal disease and we sequenced the same fungi twice, but with different extraction times. One 11 years ago and the another one this year. The strain was extracted...

04 October 2020 271 8 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Chlorinated organic formation in odor control scrubbers using hypochlorite?

I'm involved in a study of odor control technologies for municipal wastewater treatment plant. One of the control options involves a chemical 2-stage (acid/alkaline) packed bed scrubber. The...

03 March 2021 3,661 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View