Is there any recipe of electrodepositing TiO2 which does not need an annealing step above 200 0C?

Mojtaba Abdi Jalebi @Mojtaba_Abdi_Jalebi

05 May 2016 1 8K Report

We need to electrodeposit TiO2 on ITO which will lose its conductivity after annealing above 200-250 oC. We want to know if there is any recipe of ED of TiO2 which does not need an annealing step. In addition, we want to have crystalline TiO2!

Vinay Sharma

Try to deposit TiO2 using electrophoretic deposition at high electric field using TiO2 nanoparticles and just bake that film at 250 degree so that organic polymers burned out and you will get a good TiO2 film.

Badges
Science method

Similar topics
Methodology
Crystallography

More Mojtaba Abdi Jalebi's questions See All

Does the shape of metal contact pattern (e.g. Au) effect on the performance of Perovskite solar cells?

Please see below images of the full perovskite cells which have a gold pattern with different shape!

05 June 2016 3,732 5 View

Does annealing ITO substrate at more than 400 oC change its properties (e.g. conductivity)?

Why a typical Perovskite or Dye solar cell based on ms-TiO2 (which needs annealing at 500 oC) does not work when we use ITO substrates?

04 May 2016 5,732 5 View

How do I calculate the exact values of Series and Shunt resistance of a solar cell from a single IV curve?

I would like to know the easiest way to calculate Series and Shunt resistance of a solar cell from a single IV curve?

11 December 2015 1,738 20 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View