Is there any mechanical component made up of fiber reinforced composite, that exposed to creep and fatigue??

More Tesfaye Meseret Abebe's questions See All

What are thermo structural composite materials? what are their critical parametrs for modelling failures of such materials?

When does the concept thermo structural materials begin?

10 November 2016 125 1 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

Pramod Vadavkar

Dear Tesfaye,

Composite pipes / pressure vessels, chemical tanks, filament wound rotors for electric generator are some components subjected to thermal and cyclic load.

Serge V. Shil’ko

Following the Pramod Vadavkar list of examples, one can add the body jet engine as most striking example of composite structure subjected to thermal and cyclic load. Best regards

Sabarinath Pandurengan

refer journal of polymer analysis and characterization. you can find many applications in fiber reinforced composites

Emad Kamil Hussein

DEAR ALL

MANY PROSTHETIC COMPONENTS (AS LIKE SOCKETS FOR BK OR AK AMPUTATION) ARE GOOD EXAMPLES FOR SUCH COMPONENTS

Tesfaye Meseret Abebe

I thank you all!