Is there any instance where BELBIC has been used in MIMO systems?

12 December 2017 1 7K Report

I am trying to find instances where BELBIC has been used for control of multivariable processes such as distillation columns or any other MIMO systems. Instances from peer reviewed journals which are indexed in SCI are most welcome.

Kulvir Singh

DEAR Biswajit Debnath

PFA ONE RECENT PARER ON THE SUBJECT.

Brain Emotional Learning Based Intelligent Decoupler for Nonlinear Multi-Input Multi-Output Distillation Columns

Badges
Science topic

Similar topics
Academic Journals

More Biswajit Debnath's questions See All

Is it possible to measure power of a 3-phase delta connected system with 2-wattmeter method under Unbalanced conditions ?

I just want to know if this is possible. Please provide with suitable references.

08 September 2018 9,699 8 View

What is the difference between a "stabilizable" and a "strongly stabilizable" system with respect to control theory?

I am going through a rough patch in understanding what exactly is the difference between the two type of systems. In the book " Control System Synthesis : A Factorization Approach " it is...

06 July 2018 1,837 0 View

How to mathematically write " |G(s)| < 1 at all frequencies " ?

I want to include a condition for the transfer function G(s) which is equivalent to the statement mentioned above inside inverted commas but I am not able to describe it mathematically. I was...

05 June 2018 9,410 17 View

Why isn't a proper vaccine still not available for Nipah virus in India ?

We claim to be doing pretty good in the area of health care and pharmaceuticals but still we haven't been able to come up with a formidable solution for the Nipah virus. Why ? Does this indicate...

05 June 2018 3,633 2 View

How do I interpret the singular value plot shown here ?

I have a Twin Rotor MIMO system represented by a 2x2 transfer matrix. I have identified 3 different models for the same using different ways. Let's say the three different transfer matrix are...

02 March 2018 4,267 7 View

How to perform model order reduction ?

I have a MIMO system represented by a transfer matrix, the determinant of which is of order 14. How do I reduce the order of the system without compromising the original behaviour of the system ?

01 February 2018 7,555 4 View

What is meant by the term 'nominal stability' in the context of control systems ?

I have come across the term 'nominal stability' in the book 'multivariable feedback control' by Skogestad and I would like to know what it actually means. I know it has got something to do with...

01 February 2018 6,456 3 View

How to understand the Euler-Lagrangian equations for TRMS?

I would like to know about some good text books that would help me understand the derivation of the models of Euler-Lagrange equations for the TRMS models as shown in the paper attached below. I...

31 December 2017 8,179 0 View

How effective is singular value decompostion (SVD) in determining the interloop interactions in MIMO systems?

I want to ascertain the level of interaction in a MIMO process and I am looking at various ways of doing that. I came across the SVD method in the book by Seborg and I would like to know how...

10 November 2017 1,306 4 View

Can I have a decoupler with an improper transfer function?

After due calculations, if certain elements of the decoupler matrix turns out to be improper (numerator having higher degree than denominator) then, can this be implemented. I think that it will...

10 November 2017 8,655 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

Can I use a HisTRAP column for affinity chromatography?

I'm working on selecting antibodies against a recombinant protein that has a His-tag. My idea is to first bind the recombinant protein to a HisTRAP column and then use this column for an affinity...

07 August 2024 505 3 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

How can we use mobile apps for improving students' academic performance?

Mobile apps can be a powerful tool for enhancing academic performance, how can we use mobile apps for improving academic performance

04 August 2024 9,492 0 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View