How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

Can i quantify protein concentration in sds page?

I have to quantify a mixture of proteins. But I can not quantify its concentration by any protein detection methods as the values fluctuate. Can i quantify the protein concentration by sds page?

22 February 2021 215 2 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

Can we use image data in MATLAB Neuro Fuzzy Designer ?

I have remotely sensed data (image) that I want to use in the Neuro-Fuzzy Designer apps of MATLAB. Is it possible to use an image file in the Neuro-Fuzzy Designer app or only numeric data is...

17 February 2021 1,205 5 View

Is it possible to determine % K2O of organic manures by STPB method ?

To determine % K2O of organic manures, flame photometric technique is used whereas in inrganic fertiliser for K2O determination STPB method is used. I am trying to find out any method of...

24 January 2021 4,714 3 View

How to tackle "CONSTRAINT CONTROLS" error while using tie between CFRP and frame segment in abaqus?

Hello, I had been trying to model a portal frame wrapped with CFRP in ABAQUS. To tie the CFRP laminates with frame I need to use slave/master surface interaction. But whenever I try to model the...

19 January 2021 2,906 3 View

How to remove colour from DNA pellet during DNA extraction?

I am working with Amaranth accessions which are green to red in color and contain high phenolic compounds. Using the CTAB method with the slight modification I am trying to get high-quality DNA so...

18 January 2021 3,578 1 View

Why the mixture of NaOH solution (10-12M) and Na2SIO3 solution is getting solidify after mixing?

These days I am noticing that the mixture of NaOH (NH) (10-12M) and N2SiO3 (NS) solution gets solidify after 24 hours. The ratio of mixture of NS to NH is 2. To mention, the same solutions that we...

18 January 2021 7,911 2 View

Which model is most suitable for urban simulation?

Respected sir/mam, I want to simulate the urban expansion using different time series LULC based on satellite image. please suggest me most suitable model for urban simulation. Thanks and regards.

17 January 2021 9,134 11 View

Is there any packages or code of MATLAB for solving a system of stochastic delay differential equation?

Hello, Can you help me regarding MATLAB solver for a system of stochastic delay differential equations? To be specific the system is delay differential equation where parametric stochasticity is...

15 January 2021 6,950 7 View

How UAV or drone can be beneficial to better estimate crop yield?

As we know, crop yield estimation has been done traditionally with farmer's expert knowledge, deductive sampling in representative areas, and remote sensing with satellite imagery. Farmer's Expert...

01 March 2021 3,468 3 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Where i will get the Desmodium and Napier grass seeds?

26 February 2021 975 4 View

Recalcitrant seed short-mid storage method?

Dear peer scientists, Ultradry storage is not suitable for recalcitrant seeds. However, theoretically, if we can stabilize the structure of the subcellular membrane, as well as glassify the...

25 February 2021 2,442 1 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

What are the LAB methodologies (procedures, equipment etc) for CO2 enrichment experiments to study crop responses?

I am doing a proposal for a research entitled 'GRAIN YIELD AND QUALITY RESPONSES OF WHEAT GENOTYPES UNDER CO2 ENRICHMENT AND EXTREME EVENTS' I will be using climate chamber and I would like to...

18 February 2021 6,494 4 View

Is it possible to use maize mature seed to do transformation for maize transgenic study?

Almost all research reports which i ever seen work on Early mature embryo for Agrobacterium mediated maize transformation. In other grass families like rice, we can use mature seed and what do...

17 February 2021 1,434 13 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

How to differentiate the economic productivity in agriculture and in manufacturing sector?

Most of the references I found were on the economic productivity in agriculture but very limited application in manufacturing sector. I would appreciate if anyone could share the references on...

15 February 2021 8,342 7 View