Irreversibility and reversibility...

Maamar Khalleefah Aboubakr @Maamar-Aboubakr

01 January 1970 0 9K Report

What is the meaning of irreversibility for chemisorption process of the inhibitor and the metal surface?

This mean i can not use it another time or there is another mean?

Badges
Science topic

Similar topics
Phytochemistry
Extracts

More Maamar Khalleefah Aboubakr's questions See All

I want to simulate a privacy-preserving algorithm in MQTT for IoT devices, but I'm not sure which simulation software is best suited for this?

I want to apply a privacy-preserving algorithm in MQTT for IoT devices. Which tool do you suggest to simulate this algorithm? I want to measure the performance on the IoT battery device? Actually,...

28 January 2021 9,561 3 View

Will the quality of the bibliographical references and consequently the richness of a scientific research depend on modernity or variability or other?

bibliographical references in thesis or paper or any scientific research

17 March 2020 2,618 3 View

Which is the best low-cost IOT embedded board available in the market?

08 September 2018 7,273 8 View

Is it useful to use online data servers platforms like ThingSpeak or it is better to create my own platform?

I would like to know from researchers who are working on IOT, Is it useful to use online data servers platforms like ThingSpeak or it is better to create my own platform?

09 April 2018 2,251 4 View

Does anyone have this tool (River Bathymetry Toolkit (RBT)) for ArcGis 10 to compute the offset of the river?

See above

03 April 2014 7,817 2 View

What is the relation between the mechanism of adsorption and thermodynamic parameters?

I read some publications stated that the value of enthalaply change higher than 40 kJ/mol the adsorption will be chemisorption and below this value will be physisorption he negative values of...

22 November 2020 8,353 5 View

Why is there an absence of peak/s in the NH3-TPD analysis of silica ?

The NH3-TPD of commercial silica (S.A= 223m2/g) has been run on a Micromeritics 2900 AutoChem II Chemisorption Analyser to determine total acidity. However, there was no peak observed post-run....

29 April 2020 2,174 3 View

What are the methods that can be used study adsorption by using Gaussian.?

Dear sir/ madam I am studying about filtration of pesticides. how can I study the adsorption pesticides to the filtering medium using DFT in Gaussian 09. I have already tired using homo lumu...

05 June 2019 3,874 2 View

Would you please suggest what finding might be analyzed from BET data (Hg vapor absoprtion) on pellet with high content of S?

Here with I attach BET data of Hg vapor adsorption on pellet with high content of sulfur, what is the possible finding might be obtained, Is there possibility a reaction between Hg vapor with S...

31 December 2017 5,232 4 View

Is one monolayer coverage adsorption considered a high or a low coverage?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

08 September 2016 2,822 0 View

How i can quantify the active sites on iron oxide nanoparticles?

i intend to characterize and quantify total active sites on the surface of iron oxide nanoparticles during the catalytic study on aqueous based pollutants. if the reaction is on gas system model,...

03 April 2016 1,049 4 View

How to detect the amount of CO gas absorbed by graphene?

I am preparing for detecting the absorption amount of graphene, but cannot find a suitable method about this. CO gas is easy to escape and we haven't a specialized instrument. So would you please...

17 December 2015 222 3 View

How to detect the amount of CO gas absorbed by graphene?

I am preparing for detecting the absorption amount of graphene, but cannot find a suitable method about this. CO gas is easy to escape and we haven't a specialized instrument. So would you please...

11 December 2015 8,451 3 View

Our TPD instrument is not showing the proper curve for drift He experiment.. can any one help us?

Hi all. Our Autochem TPD instrument is facing one kind of problem as you can see in attachment baseline is not getting stable. What are the remedies for that? On the right side analysis taken for...

11 December 2015 9,848 3 View

What is the most suitable chemisorption probe gas to perform chemisorption of Cu based samples?

I would like to perform chemisorption of CuO depostied on carbon substrate. I have performed that analysis using H2 as the chemisorption probe. I am getting very less active metal surface area....

01 February 2015 1,635 6 View