How do i prove oocyte incompetence?

the is because the preliminary result of superovulation with (400-560 mcg) stimufol among unflushed cows did not yield any embryos 10 cows each were treated with graded doses of stimufol (400,...

13 January 2021 3,618 2 View

How to better analyse the Dynamic correlation matrix (DCCM)?

Hi everyone, is there a software or better way to compare and analyze DCCM results between two or more complexes?

28 December 2020 1,821 2 View

How to calculating association and dissociation constants between two protein after MD simulation?

I am trying to calculate both association and dissociation constants between two proteins after MD simulation but my script isn't working. I need someone to kindly assist with script(s) or...

14 December 2020 3,110 1 View

How to run second generation unit root testing on eviews-11?

After running cross section dependence test on Eviews-11, the result shows the presence of cross-section dependence. Possible cause is the interdependence of country considered in the study....

15 November 2020 8,919 1 View

How do I design MethyLight primer/probe?

I am currently working on gene-specific methylation using the MethyLight technique and I am searching for a method to design primer and probe for this technique.

02 November 2020 275 2 View

Can I run a panel regression and time series regression for comparison?

I am writing my master dissertation on impact of Microfinance in economic growth and poverty reductio. I have 5 cross-countries trekking 20 years. This makes my data a panel data, however if I run...

01 November 2020 5,650 5 View

Please i'm a new user of SAS, I need the steps to analyze a soybean data, comparing same dependent variables of 15 locations?

The design is RCBD, 16 entries, 3 reps, 4 blocks, Name. The dependent variables are date of flowering, Flower Color, Date of maturity, Daymat, Grainkha Pop_000, Dayfl, Shat2wk, Shat3wk,...

14 June 2020 571 4 View

How can I adjust a vector map in ArcGIS?

I have an imagery and the road map of the imagery location. I overlaid the imagery on the road map and there is deviation of about 6m. Someone should help me out for the solution.

08 October 2019 1,625 2 View

How do I get detailed explanation of a 4 by 5 Split plot design and how to analyse an experiment with such design using Analysis of Variance (ANOVA)?

Using a 4 by 5 Split Plot Design layout, there are 20 panelists for sensory evaluation. There are 4 different samples at 5 different concentrations. I need detailed explanation on WHOLE PLOT,...

23 October 2018 9,286 3 View

Cutting a dimer insert?

I already dimerized an insert in a vector and now trying to cut the dimer for further cloning; since there are no suitable clean ways to this, I intend to do a full xbal digest of the vector (It...

08 May 2018 5,295 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

The procedure compute?

02 March 2021 5,204 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

If you haven't computer? how you show the photons to pupils?

Educational Process

01 March 2021 1,827 1 View

Please can i get topic and materials that will relate computer with telecommunication companies?

I am a master student and i am working on my research, so I am a bit confuse don't really know how to match computer with telecommunication as a topic

28 February 2021 7,039 6 View