Hint: in America it is nearly 1/3.
In Italy is about 1\3, too.
The nonmetallic inclusions are problematic particles that develop during the steel making process. They are tiny entities that exist in high numbers. They disrupt the mechanical homogeneity of the...
31 December 2014 7,761 16 View
There are a few points being raised lately on the first direct evidence on the universe inflation and the detection of gravitational waves: 1. The cosmic microwave polarization patterns referred...
04 May 2014 4,140 3 View
The egg is one of the unique feats of natural engineering. Its three-dimensional arch structure can support the weight of a standing human being yet it is so delicate that a baby bird can peck its...
03 April 2014 4,654 4 View
This question is open for chemists, metallurgists, physicists and astrophysicists: Check out this diagram which has been released today on Universe inflation. It describes how the universe has...
03 April 2014 329 22 View
In case for example the status 'With Editor' did not change for two months or so, Are there risks of any kind the corresponding author should be aware of when reaching the journal's editorial...
02 March 2014 7,100 2 View
Please see attached this figure from a journal paper I am currently reviewing. I made slight changes to it to maintain the anonymity. The paper addresses the significance of H2S with the...
02 March 2014 6,537 1 View
Please check out these potentiodynamic profiles for experiments I recently carried out: it shows potentiodynamic scans for a pipeline steel immersed in CO2-saturated solutions of different...
02 March 2014 3,069 13 View
I am currently reviewing a research paper presenting an electrochemical study on corrosion-enhanced erosion. It attempts to link the CFD of a modeled flow to the corrosion rates of an elbow made...
02 March 2014 4,297 5 View
Please check out this question excerpted from a standardized test for high-school students in a North American country; It says: Which of the following would be a graph of speed vs. time for the...
02 March 2014 8,400 3 View
To test the corrosion behavior (or resistance) of an engineering material in an aqueous medium one can carry out immersion tests for specific periods of time across which the mass loss and...
02 March 2014 4,690 11 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Chemical Engineering /Food Engineering
20 July 2024 4,152 4 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...
10 July 2024 2,789 4 View
