If O2 sensor in glovebox indicate 120 ppm, will it affect the lithium battery performance and fabrication?

More m.z Kufian's questions See All

How to calculate Theoretical specific energy of Lithium air battery (LAB) using non-aqueous solvent and aqueous solvent?

Hi, Anyone can share information for calculate the Theoretical specific energy of Lithium air battery (LAB) ? Many journal reported the theoretical specific energy included oxygen mass are; 1....

23 June 2020 284 0 View

How to measure the distance of chromaticity coordinates and efficiency?

how can we calculate distance and efficiency the chromaticity coordinates from LED wavelength?

15 June 2017 8,517 3 View

Does anyone know about fish diagnostics?

did anyone know the best procedure for fish diagnostic or any centre/institutes/universities that have been done it successfully?

16 June 2015 6,012 8 View

Why should we test the sample at 60oC when study Li+ dendritation?

01 September 2014 341 0 View

Spss test recommendded?

Discussion Hello. Currently im trying to find significant relationship between my independent variable (level of nicotin addiction - four sub category) and dependent variable ( depression - four...

01 January 1970 972 10 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Why chloride turns into chlorine gas in a Downs cell?

I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...

03 August 2024 5,384 0 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

Good day!! All, can anyone recommend the best battery related journals to download research articles please?

I am an Mphil research student and looking for high impact factor battery related journals to download and read research articles to improve my knowledge and get new ideas in the field of battery...

01 August 2024 6,516 2 View

I obtain two plateu instead of one in LFP cathode assembled with graphite anode in 1M LiTFSI in DOL/DME, what does this mean?

I have attached the charging curve from the battery tester for review. I need help on what is happening

21 July 2024 6,898 2 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

Hello, please if any researcher work in ion battery help me,?

I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture

14 July 2024 7,702 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

How to realize charge and discharge of in-situ batteries in PPMS? Is there any expert scholar who can give me some advice?

The difficulty lies in how to miniaturize the battery. The sample holder is only 6.5mm, which means that the width or height of the battery cannot exceed 6.5mm (the height is about 3cm). I hope...

05 July 2024 8,141 0 View

Sujoy Sarkar

It is better not to fabricate the Li-battery under such condition, wait until it comes down below 10-20 ppm.

Mikhail Khimchenko

Dear Mr. Kufian, it is important just for follow for the same conditions like for basic situation. Mass-production of batteries can be realized into dry-room conditions ( dri air atmosphere). But if you plan some experiments for example with melting of Li, please reduce O2 concentration for minimal possible.