I want to attach a diesel Engine for my 12HP air blower. How do calculate the optimum engine size?

More Arun Vijayan's questions See All

I want to know the parameters of the paper to design a paper antenna in hfss?

i want to know parameter details of the normal paper like, permeability, bulk conductivity, dielectric loss tangent, magnetic loss tangent, magnetic saturation, lande G factor, delta H, mass...

07 August 2016 3,271 7 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Good morning research fellows, Has anyone worked with senna alata plant extract on any kind of fish?

Literatures on the piscicidal effect of sennaa alata is scanty. if you have any related litrature either in the bark, leaves or roots used as treatment to any aquatic organism please kindly help...

28 February 2021 9,138 2 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Experimental Design: How deal with pseudreplicates with immunological and clinical-chemical paramaeters?

Hello everybody, I am investigating the influence of a toxinon various clinical-chemical and haematological parameters in fish. I have three treatments (control, low dose, high dose) in my...

24 February 2021 1,243 1 View

Hi i want to ask that in order to find out LC 50 (96 hours) of particular toxin for fish. Should we keep the animals with food or without food?

if we expose the fish after acclimatization to particular toxin in order to find out LC 50 (96 hours).Should we keep the fish off feed or with feed for that duration. Some literature show that...

24 February 2021 357 2 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

Syed Mughees Ali

Dear Arun,

You question itself provides an answer. Go for slightly larger then 12 Hp engine.

Arun Vijayan

Dear sir, the word larger carries the value of lot of things.

That means 12.1 HP is also larger and 40HP, 100 HP , 150 HP all are comes under that word.

I'm asking the optimum range of diesel engine HP to match the practical 12 HP Genset/ Pump/ blower/ compressor.

Dear syed,

I want to add something more to you to think. What ever the load like Genset or pump or blower or compressor, if we are going to connect the electric motor means we want to connect the 1.2 to 1.4 times HP power of the actual load. 12HP load needs 1.4*12HP~ 15HP motor. If

we start the electric motor by star delta concept means 13.5 HP is enough for the 12HP load.

But the diesel engine does not have similar efficiency like electric motor. So now what is the optimum range to choose the diesel Engine.