Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

01 March 2021 8,087 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Hi i want to ask that in order to find out LC 50 (96 hours) of particular toxin for fish. Should we keep the animals with food or without food?

if we expose the fish after acclimatization to particular toxin in order to find out LC 50 (96 hours).Should we keep the fish off feed or with feed for that duration. Some literature show that...

24 February 2021 357 2 View

Errors in DNA sequences?

I am trying to better understand the scope of DNA replication and sequencing errors, e.g. 1. I have seen similar error rates of 10e4 to 10e5 for cell & instrumental DNA replication,...

24 February 2021 4,397 3 View

Does PHA-P stimulate the proliferation of lymphocytes from mice?

Hello, I will start performing MLR using lymphocytes from mice's spleen and I would like to know the better way for the stimulation. If is using PHA-P or CD3/CD28? I would like to know as well if...

23 February 2021 5,476 4 View

Could not amplify CD28 and CD3z ectodomain from cDNA of Jurkat Cells ?

For my experiments, I have to express ectodomains of human CD28 and CD3z. As a source, I extracted RNA from Jurkat cells and verified the quality of RNA on the gel. I, then, prepared cDNA using...

23 February 2021 7,051 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

Can we recognize signs of the "volatility clustering" property of a time series in its time domain plot?

My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.

24 February 2021 4,150 3 View

RNA degraded after good nanodrop readings?

23 February 2021 8,850 2 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View