I have an L section of multiyayer slab and i want to calculate the over all conduction ?

05 May 2019 1 4K Report

If i want to calculate the over all conduction should i consider all the connection in series or the base will be in parallel to the side walls

Ievgen Lavrukhin

Ramesh Siripuram, I think the right way is to consider the connection is series. There is a nice online resource where you can look at the examples of calculating a conduction of a composition flat wall: http://fc.civil.tamu.edu/resources/en/engr214/Chapter7/node13.html

I hope it will be helpful for you.

Badges
Science topic

More Ramesh Siripuram's questions See All

How to simulate vaccum using CFD in ansys and which module provides better result?

hello i have a geometry which looks like complex cylinder wall where the space between the two walls is filled with vaccum and the inner volume is to be filled with liquid nitrogen how can...

07 August 2019 1,360 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Microtome tissue sectioning - How to prevent chatter of paraffin tissue specimen sections?

Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...

06 August 2024 666 4 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,627 1 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Do we put respondents data in research methods or findings section of a qualitative study?

Are both ways acceptable, or is there any convention to them? Thanks.

22 July 2024 6,988 4 View